Looking for reliable CNC Gear Grinding Brass? VT machining manufactures Brass parts to tight tolerances and consistent quality. Brass is free-machining, good conductivity, attractive finish, so the process is set up specifically for the material.
CNC Gear Grinding Capability for Brass
- DIN/AGMA accuracy class
- Profile & lead correction
- Hardened-gear finishing
- Low transmission noise
Brass Material Data
| Density | 8.50 g/cm³ |
|---|---|
| Tensile strength | 340–470 MPa |
| Yield strength (0.2%) | 125–310 MPa |
| Hardness | 78–130 HB |
| Melting point | 885–900 °C |
| Thermal conductivity | 115 W/m·K |
| Thermal expansion | 20.5 ×10⁻⁶/K |
| Electrical conductivity | 26% |
| Machinability (C36000 = 100%) | 100% (the benchmark) |
| Grades we run | C36000 free-cutting, C37700 forging, C26000 cartridge, C46400 naval |
Published typical values for C36000. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Nothing much — this is the easiest metal in the shop. Worth asking about if a copper or bronze part is cost-driven rather than conductivity-driven.
How CNC Gear Grinding Brass Works
Tooth profiles are generated in the Brass blank by a synchronised cutter, then refined to the required accuracy class. Module, pressure angle and helix are programmed from your gear data.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Gear Grinding Brass
| Feature | Standard | Precision |
|---|---|---|
| Accuracy class | DIN 8 / AGMA 10 | DIN 6 / AGMA 12 |
| Profile deviation | 0.020 mm | 0.008 mm |
| Lead deviation | 0.020 mm | 0.008 mm |
| Pitch deviation (cumulative) | 0.040 mm | 0.015 mm |
| Runout | 0.030 mm | 0.010 mm |
| Tooth surface finish | Ra 1.6 µm | Ra 0.4 µm (ground) |
| Module range | m0.5–m8 | m1–m6 |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Secondary Operations & Finishing
Most Brass parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Design Tips for CNC Gear Grinding Brass
Small design adjustments often cut cost and lead time. Providing complete gear data (module, pressure angle, profile shift, quality class) lets us produce Brass gears right the first time. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Gear Grinding Tolerances & Surface Finish
Gear features are produced to a specified DIN/AGMA accuracy class, with profile and lead controlled for quiet, durable running under load.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
CNC Gear Grinding Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Working with Brass
Brass is free-machining, good conductivity, attractive finish. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Applications of CNC Gear Grinding Brass
Brass parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Gear Grinding Brass
Starting your project takes one email. Send your CAD or 2D drawing, the Brass grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Brass
Three representative CNC Gear Grinding Brass jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Internal ring gear
- Material
- Brass
- Size
- m2.5, z72, ID 190 mm
- Key callouts
- DIN 8, pitch deviation 0.03 mm
- Batch
- 150 pcs
Shaped rather than hobbed — an internal gear leaves no room for a hob to run out.
Worm and wheel set
- Material
- Brass
- Size
- m3, single start
- Key callouts
- Backlash 0.05–0.10 mm as a matched pair
- Batch
- 120 sets
Supplied as matched sets and marked, because mixing pairs loses the backlash spec.
Helical pinion
- Material
- Brass
- Size
- m1.5, z18, 15° helix
- Key callouts
- DIN 6, lead deviation 0.008 mm
- Batch
- 300 pcs
Ground after case hardening to 58 HRC at 0.6 mm case depth.
Finishing Options for Brass
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Nickel plate | 5–15 µm | Hard, bright, corrosion resistant |
| Chrome plate | 0.3–1 µm | Decorative, over nickel |
| Clear lacquer | 10–20 µm | Stops the natural tarnish |
| Tin plate | 3–15 µm | Solderable contacts |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Gear Grinding Brass
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Brass grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Gear Grinding
Other Processes for Brass
Send the drawing, the Brass grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Does CNC Gear Grinding Brass require dedicated tooling?
Most Brass gear cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
Can VT machining make custom Brass parts to my drawing?
Yes. Brass Brass gear cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
How clean are the edges produced by CNC Gear Grinding on Brass?
Machined Brass edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What surface finish is achievable on Brass with CNC Gear Grinding?
Surface finish on Brass is controlled to your specification; we confirm the achievable Ra against your callout.