CNC Gear Grinding Stainless Steel is a core capability at VT machining. We combine controlled gear cutting with material-aware setup for Stainless Steel — an alloy that is corrosion resistant, strong, hygienic (304/316 grades) — to produce parts that meet your specification first time.
CNC Gear Grinding Capability for Stainless Steel
- DIN/AGMA accuracy class
- Profile & lead correction
- Hardened-gear finishing
- Low transmission noise
Stainless Steel Material Data
| Density | 8.00 g/cm³ |
|---|---|
| Tensile strength | 515 MPa |
| Yield strength (0.2%) | 205 MPa |
| Hardness | 170 HB |
| Melting point | 1400–1450 °C |
| Thermal conductivity | 16.2 W/m·K |
| Thermal expansion | 17.3 ×10⁻⁶/K |
| Electrical conductivity | 2.4% |
| Machinability (C36000 = 100%) | 45% |
| Grades we run | 303, 304/304L, 316/316L, 321, 410, 416, 420, 17-4PH, 2205 duplex |
Published typical values for 304. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
It work-hardens the moment a tool dwells. Constant feed and positive-rake tooling; a rubbing pass leaves a glazed skin the next tool cannot get through.
How CNC Gear Grinding Stainless Steel Works
Tooth profiles are generated in the Stainless Steel blank by a synchronised cutter, then refined to the required accuracy class. Module, pressure angle and helix are programmed from your gear data.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Gear Grinding Stainless Steel
| Feature | Standard | Precision |
|---|---|---|
| Accuracy class | DIN 8 / AGMA 10 | DIN 6 / AGMA 12 |
| Profile deviation | 0.020 mm | 0.008 mm |
| Lead deviation | 0.020 mm | 0.008 mm |
| Pitch deviation (cumulative) | 0.040 mm | 0.015 mm |
| Runout | 0.030 mm | 0.010 mm |
| Tooth surface finish | Ra 1.6 µm | Ra 0.4 µm (ground) |
| Module range | m0.5–m8 | m1–m6 |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Working with Stainless Steel
As a material, Stainless Steel is corrosion resistant, strong, hygienic (304/316 grades). Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
CNC Gear Grinding Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Stainless Steel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Secondary Operations & Finishing
Finished Stainless Steel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
CNC Gear Grinding Tolerances & Surface Finish
Gear features are produced to a specified DIN/AGMA accuracy class, with profile and lead controlled for quiet, durable running under load.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Design Tips for CNC Gear Grinding Stainless Steel
We are happy to suggest design tweaks that improve manufacturability. Providing complete gear data (module, pressure angle, profile shift, quality class) lets us produce Stainless Steel gears right the first time. If you send your model early, we will return practical DFM feedback before you commit to production.
Applications of CNC Gear Grinding Stainless Steel
Customers order CNC Gear Grinding Stainless Steel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Gear Grinding Stainless Steel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Stainless Steel
Three representative CNC Gear Grinding Stainless Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Internal ring gear
- Material
- Stainless Steel
- Size
- m2.5, z72, ID 190 mm
- Key callouts
- DIN 8, pitch deviation 0.03 mm
- Batch
- 150 pcs
Shaped rather than hobbed — an internal gear leaves no room for a hob to run out.
Worm and wheel set
- Material
- Stainless Steel
- Size
- m3, single start
- Key callouts
- Backlash 0.05–0.10 mm as a matched pair
- Batch
- 120 sets
Supplied as matched sets and marked, because mixing pairs loses the backlash spec.
Splined shaft
- Material
- Stainless Steel
- Size
- DIN 5480, 26 × 1.5
- Key callouts
- Fit class H7/g6, runout 0.02 mm
- Batch
- 800 pcs
Spline hobbed with the journals ground afterwards on the same centres.
Finishing Options for Stainless Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Citric passivation | — | ASTM A967 / AMS 2700, removes free iron |
| Electropolish | 5–25 µm removed | Ra improves by roughly half, hygienic surface |
| Brushed / grained | Ra 0.4–1.6 µm | No. 4 finish, directional |
| PVD coating | 2–5 µm | TiN, TiCN for wear surfaces |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Gear Grinding Stainless Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Stainless Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Gear Grinding
Other Processes for Stainless Steel
Send the drawing, the Stainless Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Does CNC Gear Grinding Stainless Steel require dedicated tooling?
Most Stainless Steel gear cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
Which industries use CNC Gear Grinding Stainless Steel parts?
CNC Gear Grinding Stainless Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Stainless Steel components are required.
What material thickness or size range suits CNC Gear Grinding Stainless Steel?
We machine Stainless Steel across a broad size range; share your part envelope for confirmation.
What is CNC Gear Grinding Stainless Steel and how is it done?
CNC Gear Grinding Stainless Steel refers to gear grinding finishes hardened gear teeth to high accuracy class for quiet, durable transmission. Applied to Stainless Steel — corrosion resistant, strong, hygienic (304/316 grades) — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What tolerances can you hold for CNC Gear Grinding Stainless Steel?
Achievable tolerances for Stainless Steel gear cutting depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.