VT machining provides CNC Tapping Brass for customers who need accurate, repeatable Brass components. Because Brass is free-machining, good conductivity, attractive finish, we adapt the process to suit — controlling the variables that matter for this alloy.
CNC Tapping Capability for Brass
- Metric & UNC/UNF threads
- Rigid synchronized tapping
- Thread depth control
- Form and cut taps
Brass Material Data
| Density | 8.50 g/cm³ |
|---|---|
| Tensile strength | 340–470 MPa |
| Yield strength (0.2%) | 125–310 MPa |
| Hardness | 78–130 HB |
| Melting point | 885–900 °C |
| Thermal conductivity | 115 W/m·K |
| Thermal expansion | 20.5 ×10⁻⁶/K |
| Electrical conductivity | 26% |
| Machinability (C36000 = 100%) | 100% (the benchmark) |
| Grades we run | C36000 free-cutting, C37700 forging, C26000 cartridge, C46400 naval |
Published typical values for C36000. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Nothing much — this is the easiest metal in the shop. Worth asking about if a copper or bronze part is cost-driven rather than conductivity-driven.
How CNC Tapping Brass Works
Rotating multi-flute cutters remove material as the Brass workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Tapping Brass
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Tapping Brass
We are happy to suggest design tweaks that improve manufacturability. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Brass. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Brass
As a material, Brass is free-machining, good conductivity, attractive finish. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
CNC Tapping Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Brass part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
CNC Tapping Tolerances & Surface Finish
For CNC Tapping, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Secondary Operations & Finishing
Finished Brass parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Tapping Brass
Customers order CNC Tapping Brass components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Tapping Brass
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Brass
Three representative CNC Tapping Brass jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Heat sink base
- Material
- Brass
- Size
- 200 × 100 × 8 mm
- Key callouts
- Fin thickness 1.2 ±0.05 mm, base flatness 0.03 mm
- Batch
- 500 pcs
Fins cut with a slotting cutter in one pass to avoid the deflection a step-over leaves.
Manifold block
- Material
- Brass
- Size
- 120 × 60 × 45 mm
- Key callouts
- Cross-bore intersection ±0.05 mm, ports G1/8", leak-tested to 10 bar
- Batch
- 80 pcs
Deburred internally with a brush tool; a burr at a cross-bore is what fails the leak test.
Sensor housing
- Material
- Brass
- Size
- 86 × 54 × 22 mm
- Key callouts
- Pocket depth ±0.02 mm, bore H7, flatness 0.015 mm
- Batch
- 250 pcs / quarter
O-ring groove finished in the same setup as the sealing face so the two stay parallel.
Finishing Options for Brass
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Nickel plate | 5–15 µm | Hard, bright, corrosion resistant |
| Chrome plate | 0.3–1 µm | Decorative, over nickel |
| Clear lacquer | 10–20 µm | Stops the natural tarnish |
| Tin plate | 3–15 µm | Solderable contacts |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Tapping Brass
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Brass grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Tapping
Other Processes for Brass
Send the drawing, the Brass grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is the typical lead time and minimum order for CNC Tapping Brass?
CNC Tapping prototypes for Brass can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
Which industries use CNC Tapping Brass parts?
CNC Tapping Brass parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Brass components are required.
Can VT machining make custom Brass parts to my drawing?
Yes. Brass Brass machining is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What is CNC Tapping Brass and how is it done?
CNC Tapping Brass refers to rigid CNC tapping cuts internal threads in sync with spindle feed for precise, repeatable thread engagement. Applied to Brass — free-machining, good conductivity, attractive finish — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Does CNC Tapping Brass require dedicated tooling?
Most Brass machining work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.