CNC Reaming Brass from VT machining delivers precision Brass parts produced to your exact drawing. Reaming finishes drilled holes to a precise diameter and smooth surface in a single controlled pass, and we tune every parameter to the behaviour of Brass, which is free-machining, good conductivity, attractive finish.
CNC Reaming Capability for Brass
- H7 hole tolerance typical
- Ra to 0.4 µm bore finish
- Carbide and HSS reamers
- Pilot-guided accuracy
Brass Material Data
| Density | 8.50 g/cm³ |
|---|---|
| Tensile strength | 340–470 MPa |
| Yield strength (0.2%) | 125–310 MPa |
| Hardness | 78–130 HB |
| Melting point | 885–900 °C |
| Thermal conductivity | 115 W/m·K |
| Thermal expansion | 20.5 ×10⁻⁶/K |
| Electrical conductivity | 26% |
| Machinability (C36000 = 100%) | 100% (the benchmark) |
| Grades we run | C36000 free-cutting, C37700 forging, C26000 cartridge, C46400 naval |
Published typical values for C36000. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Nothing much — this is the easiest metal in the shop. Worth asking about if a copper or bronze part is cost-driven rather than conductivity-driven.
How CNC Reaming Brass Works
Rotating multi-flute cutters remove material as the Brass workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
Every job begins from your CAD model or 2D drawing. Fixturing and tool paths are planned so the most critical dimensions are produced in the most rigid, repeatable setup. Critical dimensions are checked on the first part and monitored through the run.
Achievable Tolerances for CNC Reaming Brass
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Secondary Operations & Finishing
We complete Brass components with the secondary steps your drawing calls for. We arrange heat treatment, surface treatment, marking and assembly as needed. Tell us the final spec and we will plan the full route so parts arrive ready to use.
Working with Brass
Brass offers a useful combination of properties: it is free-machining, good conductivity, attractive finish. Those characteristics shape how we approach milling — from tool and parameter selection to work-holding and coolant.
If your application is sensitive to alloy condition, we agree the specification in writing and document it. Stock is sourced from reputable suppliers so what you order is what you receive.
CNC Reaming Quality & Inspection
Consistent quality comes from disciplined process control. Critical dimensions on Brass parts are checked in-process and verified at final inspection using calibrated instruments and, where required, CMM measurement. Full documentation — dimensional reports, mill certs, FAIR — is available when your programme needs it.
Design Tips for CNC Reaming Brass
A few design choices make a real difference to cost and quality. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Brass. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Reaming Tolerances & Surface Finish
For CNC Reaming, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
Final tolerances are governed by the material's behaviour, wall thickness and overall stiffness. We give honest DFM feedback if a callout would be costly or better achieved another way.
Applications of CNC Reaming Brass
CNC Reaming of Brass supports parts across aerospace, medical, automotive, electronics, semiconductor, energy and general industrial sectors. We scale from one-off prototypes to ongoing production while holding the same quality.
How to Order CNC Reaming Brass
Ordering Brass parts is straightforward. Provide the drawing, material, quantity and any certification needs. Our engineers reply — in English — with feasibility, pricing and a realistic lead time, usually within one business day.
Parts We Have Run in Brass
Three representative CNC Reaming Brass jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Vacuum chamber flange
- Material
- Brass
- Size
- Ø180 × 20 mm
- Key callouts
- Knife-edge seal Ra 0.4 µm, bolt circle ±0.05 mm
- Batch
- 60 pcs
Sealing face finished last, then handled in gloves and bagged straight off the machine.
Optical mount plate
- Material
- Brass
- Size
- 160 × 160 × 12 mm
- Key callouts
- Hole pattern true position ±0.02 mm, flatness 0.01 mm
- Batch
- 40 pcs
Roughed, stress-relieved overnight, then finished — the plate is too thin to hold flatness in one hit.
Sensor housing
- Material
- Brass
- Size
- 86 × 54 × 22 mm
- Key callouts
- Pocket depth ±0.02 mm, bore H7, flatness 0.015 mm
- Batch
- 250 pcs / quarter
O-ring groove finished in the same setup as the sealing face so the two stay parallel.
Finishing Options for Brass
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Nickel plate | 5–15 µm | Hard, bright, corrosion resistant |
| Chrome plate | 0.3–1 µm | Decorative, over nickel |
| Clear lacquer | 10–20 µm | Stops the natural tarnish |
| Tin plate | 3–15 µm | Solderable contacts |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Reaming Brass
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Brass grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Reaming
Other Processes for Brass
Send the drawing, the Brass grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Why is Brass a good choice for CNC Reaming?
Brass is free-machining, good conductivity, attractive finish, which makes it well suited to CNC Reaming. We tune the process to the alloy so the finished Brass machining part meets your dimensional and functional requirements.
Which industries use CNC Reaming Brass parts?
CNC Reaming Brass parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Brass components are required.
What tolerances can you hold for CNC Reaming Brass?
Achievable tolerances for Brass machining depend on the alloy, geometry and feature size. Milling holds positional and dimensional tolerances to around ±0.01 mm, tighter with precision setups. Exact figures are confirmed against your drawing callouts.
What is the typical lead time and minimum order for CNC Reaming Brass?
CNC Reaming prototypes for Brass can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
What is CNC Reaming Brass and how is it done?
CNC Reaming Brass refers to reaming finishes drilled holes to a precise diameter and smooth surface in a single controlled pass. Applied to Brass — free-machining, good conductivity, attractive finish — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
How clean are the edges produced by CNC Reaming on Brass?
Machined Brass edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.