CNC Reaming Steel from VT machining delivers precision Steel parts produced to your exact drawing. Reaming finishes drilled holes to a precise diameter and smooth surface in a single controlled pass, and we tune every parameter to the behaviour of Steel, which is strong, economical, widely available carbon/alloy grades.
CNC Reaming Capability for Steel
- H7 hole tolerance typical
- Ra to 0.4 µm bore finish
- Carbide and HSS reamers
- Pilot-guided accuracy
Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 585 MPa |
| Yield strength (0.2%) | 450 MPa |
| Hardness | 170 HB |
| Melting point | 1420–1460 °C |
| Thermal conductivity | 51.9 W/m·K |
| Thermal expansion | 11.5 ×10⁻⁶/K |
| Electrical conductivity | 9% |
| Machinability (C36000 = 100%) | 57% |
| Grades we run | 1018, 1045, 1215, A36, S45C, St37, 4140 (see alloy steel) |
Published typical values for 1045. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Rust. Bare steel flash-rusts within hours in a humid container, so parts are oiled or passivated before packing unless you specify otherwise.
How CNC Reaming Steel Works
Rotating multi-flute cutters remove material as the Steel workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Reaming Steel
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Working with Steel
Steel is strong, economical, widely available carbon/alloy grades. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Secondary Operations & Finishing
Most Steel parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Design Tips for CNC Reaming Steel
Small design adjustments often cut cost and lead time. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Steel. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Reaming Tolerances & Surface Finish
For CNC Reaming, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
CNC Reaming Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Applications of CNC Reaming Steel
Steel parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Reaming Steel
Starting your project takes one email. Send your CAD or 2D drawing, the Steel grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Steel
Three representative CNC Reaming Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Heat sink base
- Material
- Steel
- Size
- 200 × 100 × 8 mm
- Key callouts
- Fin thickness 1.2 ±0.05 mm, base flatness 0.03 mm
- Batch
- 500 pcs
Fins cut with a slotting cutter in one pass to avoid the deflection a step-over leaves.
Manifold block
- Material
- Steel
- Size
- 120 × 60 × 45 mm
- Key callouts
- Cross-bore intersection ±0.05 mm, ports G1/8", leak-tested to 10 bar
- Batch
- 80 pcs
Deburred internally with a brush tool; a burr at a cross-bore is what fails the leak test.
Sensor housing
- Material
- Steel
- Size
- 86 × 54 × 22 mm
- Key callouts
- Pocket depth ±0.02 mm, bore H7, flatness 0.015 mm
- Batch
- 250 pcs / quarter
O-ring groove finished in the same setup as the sealing face so the two stay parallel.
Finishing Options for Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Black oxide | 1–2 µm | Mild corrosion resistance, no dimensional change |
| Zinc plate + clear/yellow | 5–12 µm | ASTM B633, general corrosion protection |
| Nickel plate (electroless) | 10–25 µm | Uniform in bores, 500 HV after bake |
| Phosphate | 5–10 µm | Paint key, mild lubricity |
| Powder coat | 60–120 µm | RAL colours |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Reaming Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Reaming
Other Processes for Steel
Send the drawing, the Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Can VT machining make custom Steel parts to my drawing?
Yes. Steel Steel machining is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
Does CNC Reaming Steel require dedicated tooling?
Most Steel machining work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What surface finish is achievable on Steel with CNC Reaming?
Surface finish on Steel is controlled to your specification; we confirm the achievable Ra against your callout.
Which industries use CNC Reaming Steel parts?
CNC Reaming Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Steel components are required.