Looking for reliable CNC Gear Grinding Steel? VT machining manufactures Steel parts to tight tolerances and consistent quality. Steel is strong, economical, widely available carbon/alloy grades, so the process is set up specifically for the material.
CNC Gear Grinding Capability for Steel
- DIN/AGMA accuracy class
- Profile & lead correction
- Hardened-gear finishing
- Low transmission noise
Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 585 MPa |
| Yield strength (0.2%) | 450 MPa |
| Hardness | 170 HB |
| Melting point | 1420–1460 °C |
| Thermal conductivity | 51.9 W/m·K |
| Thermal expansion | 11.5 ×10⁻⁶/K |
| Electrical conductivity | 9% |
| Machinability (C36000 = 100%) | 57% |
| Grades we run | 1018, 1045, 1215, A36, S45C, St37, 4140 (see alloy steel) |
Published typical values for 1045. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Rust. Bare steel flash-rusts within hours in a humid container, so parts are oiled or passivated before packing unless you specify otherwise.
How CNC Gear Grinding Steel Works
Tooth profiles are generated in the Steel blank by a synchronised cutter, then refined to the required accuracy class. Module, pressure angle and helix are programmed from your gear data.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Gear Grinding Steel
| Feature | Standard | Precision |
|---|---|---|
| Accuracy class | DIN 8 / AGMA 10 | DIN 6 / AGMA 12 |
| Profile deviation | 0.020 mm | 0.008 mm |
| Lead deviation | 0.020 mm | 0.008 mm |
| Pitch deviation (cumulative) | 0.040 mm | 0.015 mm |
| Runout | 0.030 mm | 0.010 mm |
| Tooth surface finish | Ra 1.6 µm | Ra 0.4 µm (ground) |
| Module range | m0.5–m8 | m1–m6 |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Gear Grinding Tolerances & Surface Finish
Gear features are produced to a specified DIN/AGMA accuracy class, with profile and lead controlled for quiet, durable running under load.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Working with Steel
As a material, Steel is strong, economical, widely available carbon/alloy grades. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
CNC Gear Grinding Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Steel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Design Tips for CNC Gear Grinding Steel
We are happy to suggest design tweaks that improve manufacturability. Providing complete gear data (module, pressure angle, profile shift, quality class) lets us produce Steel gears right the first time. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
Finished Steel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Gear Grinding Steel
Customers order CNC Gear Grinding Steel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Gear Grinding Steel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Steel
Three representative CNC Gear Grinding Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Internal ring gear
- Material
- Steel
- Size
- m2.5, z72, ID 190 mm
- Key callouts
- DIN 8, pitch deviation 0.03 mm
- Batch
- 150 pcs
Shaped rather than hobbed — an internal gear leaves no room for a hob to run out.
Worm and wheel set
- Material
- Steel
- Size
- m3, single start
- Key callouts
- Backlash 0.05–0.10 mm as a matched pair
- Batch
- 120 sets
Supplied as matched sets and marked, because mixing pairs loses the backlash spec.
Helical pinion
- Material
- Steel
- Size
- m1.5, z18, 15° helix
- Key callouts
- DIN 6, lead deviation 0.008 mm
- Batch
- 300 pcs
Ground after case hardening to 58 HRC at 0.6 mm case depth.
Finishing Options for Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Black oxide | 1–2 µm | Mild corrosion resistance, no dimensional change |
| Zinc plate + clear/yellow | 5–12 µm | ASTM B633, general corrosion protection |
| Nickel plate (electroless) | 10–25 µm | Uniform in bores, 500 HV after bake |
| Phosphate | 5–10 µm | Paint key, mild lubricity |
| Powder coat | 60–120 µm | RAL colours |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Gear Grinding Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Gear Grinding
Other Processes for Steel
Send the drawing, the Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Why is Steel a good choice for CNC Gear Grinding?
Steel is strong, economical, widely available carbon/alloy grades, which makes it well suited to CNC Gear Grinding. We tune the process to the alloy so the finished Steel gear cutting part meets your dimensional and functional requirements.
Can VT machining make custom Steel parts to my drawing?
Yes. Steel Steel gear cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What tolerances can you hold for CNC Gear Grinding Steel?
Achievable tolerances for Steel gear cutting depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.
What is CNC Gear Grinding Steel and how is it done?
CNC Gear Grinding Steel refers to gear grinding finishes hardened gear teeth to high accuracy class for quiet, durable transmission. Applied to Steel — strong, economical, widely available carbon/alloy grades — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Which industries use CNC Gear Grinding Steel parts?
CNC Gear Grinding Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Steel components are required.