VT machining provides Laser Cutting Tungsten Copper for customers who need accurate, repeatable Tungsten Copper components. Because Tungsten Copper is combines tungsten strength with copper conductivity, we adapt the process to suit — controlling the variables that matter for this alloy.
Laser Cutting Capability for Tungsten Copper
- Fiber source 1–6 kW
- Kerf width 0.1–0.3 mm
- Contour tolerance ±0.05 mm
- Assist gas (N₂/O₂) selected per alloy
Tungsten Copper Material Data
| Density | 14.8–17.0 g/cm³ |
|---|---|
| Tensile strength | 790 MPa |
| Yield strength (0.2%) | 520 MPa |
| Hardness | 220 HB |
| Melting point | 1083 (Cu phase) °C |
| Thermal conductivity | 180–200 W/m·K |
| Thermal expansion | 8.3 ×10⁻⁶/K |
| Electrical conductivity | 42–48% |
| Machinability (C36000 = 100%) | 35% |
| Grades we run | W70Cu30, W75Cu25, W80Cu20, W85Cu15 |
Published typical values for W75Cu25. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Two phases with very different behaviour in one part. EDM gives a far more consistent result than milling on fine features, and it is the usual route for heat-spreader profiles.
How Laser Cutting Tungsten Copper Works
A focused fibre-laser beam melts and blows material from the Tungsten Copper sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for Laser Cutting Tungsten Copper
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for Laser Cutting Tungsten Copper
Small design adjustments often cut cost and lead time. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Tungsten Copper. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Tungsten Copper
Tungsten Copper is combines tungsten strength with copper conductivity. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Laser Cutting Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Secondary Operations & Finishing
Most Tungsten Copper parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Laser Cutting Tolerances & Surface Finish
Laser-cut Tungsten Copper holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Applications of Laser Cutting Tungsten Copper
Tungsten Copper parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order Laser Cutting Tungsten Copper
Starting your project takes one email. Send your CAD or 2D drawing, the Tungsten Copper grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Tungsten Copper
Three representative Laser Cutting Tungsten Copper jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Battery busbar
- Material
- Tungsten Copper
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
EMI shield can
- Material
- Tungsten Copper
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Control panel face
- Material
- Tungsten Copper
- Size
- 400 × 300 × 1.5 mm
- Key callouts
- Cutout position ±0.10 mm, no dross on visible face
- Batch
- 600 pcs
Cut with nitrogen so the edge takes powder coat without secondary grinding.
Finishing Options for Tungsten Copper
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote Laser Cutting Tungsten Copper
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten Copper grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for Laser Cutting
Other Processes for Tungsten Copper
Send the drawing, the Tungsten Copper grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by Laser Cutting on Tungsten Copper?
Laser cutting leaves Tungsten Copper with a narrow kerf and a clean, near burr-free edge and only a small heat-affected zone.
What is Laser Cutting Tungsten Copper and how is it done?
Laser Cutting Tungsten Copper refers to fiber laser cutting melts and ejects metal along a programmed path, producing a narrow kerf and a clean, near burr-free edge. Applied to Tungsten Copper — combines tungsten strength with copper conductivity — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What is the typical lead time and minimum order for Laser Cutting Tungsten Copper?
Laser Cutting prototypes for Tungsten Copper can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
Can VT machining make custom Tungsten Copper parts to my drawing?
Yes. Tungsten Copper Tungsten Copper cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.