CNC Waterjet Cutting Tungsten Copper is a core capability at VT machining. We combine controlled cutting with material-aware setup for Tungsten Copper — an alloy that is combines tungsten strength with copper conductivity — to produce parts that meet your specification first time.
Process Data for CNC Waterjet Cutting Tungsten Copper
| Cutting speed at 10 mm | ~51 mm/min |
|---|---|
| Cutting speed at 25 mm | ~16 mm/min |
| Profile tolerance | ±0.1 mm; edge taper <0.05 mm with taper compensation |
| Heat-affected zone | None |
Shown for Tungsten Copper (W70Cu30-W80Cu20), the most common Tungsten Copper grade we see for CNC Waterjet Cutting. Typical values for Tungsten Copper (W70Cu30-W80Cu20), Infiltrated (pressed, sintered, Cu-infiltrated); confirmed on the first part.
CNC Waterjet Cutting Capability for Tungsten Copper
- No heat-affected zone
- Thickness to 150+ mm
- Tolerance ±0.1 mm
- Any-metal capability
Tungsten Copper material properties, finishing options and grade notes are on our CNC Laser Cutting Tungsten Copper page.
How CNC Waterjet Cutting Tungsten Copper Works
A focused fibre-laser beam melts and blows material from the Tungsten Copper sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Waterjet Cutting Tungsten Copper
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Waterjet Cutting Tungsten Copper
We are happy to suggest design tweaks that improve manufacturability. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Tungsten Copper. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Waterjet Cutting Tolerances & Surface Finish
Laser-cut Tungsten Copper holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Applications of CNC Waterjet Cutting Tungsten Copper
Customers order CNC Waterjet Cutting Tungsten Copper components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
Typical Tungsten Copper Parts for CNC Waterjet Cutting
Illustrative examples of CNC Waterjet Cutting Tungsten Copper parts and the callouts that usually drive the process plan. They show the kind of work that fits this process; they are not specific customer orders.
Battery busbar
- Material
- Tungsten Copper
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
EMI shield can
- Material
- Tungsten Copper
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Control panel face
- Material
- Tungsten Copper
- Size
- 400 × 300 × 1.5 mm
- Key callouts
- Cutout position ±0.10 mm, no dross on visible face
- Batch
- 600 pcs
Cut with nitrogen so the edge takes powder coat without secondary grinding.
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Waterjet Cutting Tungsten Copper
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten Copper grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Waterjet Cutting
Other Processes for Tungsten Copper
Send the drawing, the Tungsten Copper grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What material thickness or size range suits CNC Waterjet Cutting Tungsten Copper?
Laser-cut Tungsten Copper thickness depends on the alloy and its reflectivity; we tune the fiber source and assist gas accordingly.
Can VT machining make custom Tungsten Copper parts to my drawing?
Yes. Tungsten Copper cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What surface finish is achievable on Tungsten Copper with CNC Waterjet Cutting?
Laser cutting leaves a clean cut face on Tungsten Copper with a small heat-affected zone; most parts need little secondary finishing.
What tolerances can you hold for CNC Waterjet Cutting Tungsten Copper?
Achievable tolerances for Tungsten Copper cutting depend on the alloy, geometry and feature size. Laser cutting holds contour tolerances to around ±0.05 mm depending on thickness. Exact figures are confirmed against your drawing callouts.
What is the typical lead time and minimum order for CNC Waterjet Cutting Tungsten Copper?
CNC Waterjet Cutting prototypes for Tungsten Copper can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.