CNC Laser Cutting Tungsten Copper from VT machining delivers precision Tungsten Copper parts produced to your exact drawing. CNC fiber laser cutting follows a programmed path to cut sheet and plate with a clean, narrow kerf, and we tune every parameter to the behaviour of Tungsten Copper, which is combines tungsten strength with copper conductivity.
CNC Laser Cutting Capability for Tungsten Copper
- Fiber 1–6 kW
- Kerf 0.1–0.3 mm
- Contour ±0.05 mm
- N₂/O₂ assist gas
Tungsten Copper Material Data
| Density | 14.8–17.0 g/cm³ |
|---|---|
| Tensile strength | 790 MPa |
| Yield strength (0.2%) | 520 MPa |
| Hardness | 220 HB |
| Melting point | 1083 (Cu phase) °C |
| Thermal conductivity | 180–200 W/m·K |
| Thermal expansion | 8.3 ×10⁻⁶/K |
| Electrical conductivity | 42–48% |
| Machinability (C36000 = 100%) | 35% |
| Grades we run | W70Cu30, W75Cu25, W80Cu20, W85Cu15 |
Published typical values for W75Cu25. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Two phases with very different behaviour in one part. EDM gives a far more consistent result than milling on fine features, and it is the usual route for heat-spreader profiles.
How CNC Laser Cutting Tungsten Copper Works
A focused fibre-laser beam melts and blows material from the Tungsten Copper sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Laser Cutting Tungsten Copper
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Laser Cutting Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Tungsten Copper part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Secondary Operations & Finishing
Finished Tungsten Copper parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
CNC Laser Cutting Tolerances & Surface Finish
Laser-cut Tungsten Copper holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Design Tips for CNC Laser Cutting Tungsten Copper
We are happy to suggest design tweaks that improve manufacturability. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Tungsten Copper. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Tungsten Copper
As a material, Tungsten Copper is combines tungsten strength with copper conductivity. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Applications of CNC Laser Cutting Tungsten Copper
Customers order CNC Laser Cutting Tungsten Copper components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Laser Cutting Tungsten Copper
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Tungsten Copper
Three representative CNC Laser Cutting Tungsten Copper jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
EMI shield can
- Material
- Tungsten Copper
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Battery busbar
- Material
- Tungsten Copper
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
Bracket blank
- Material
- Tungsten Copper
- Size
- 250 × 120 × 4 mm
- Key callouts
- Contour ±0.10 mm, bend-relief notches
- Batch
- 800 pcs
Bend reliefs cut in at the same time so the press brake does not tear the corner.
Finishing Options for Tungsten Copper
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Laser Cutting Tungsten Copper
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten Copper grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Laser Cutting
Other Processes for Tungsten Copper
Send the drawing, the Tungsten Copper grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Laser Cutting on Tungsten Copper?
Laser cutting leaves Tungsten Copper with a narrow kerf and a clean, near burr-free edge and only a small heat-affected zone.
What tolerances can you hold for CNC Laser Cutting Tungsten Copper?
Achievable tolerances for Tungsten Copper cutting depend on the alloy, geometry and feature size. Laser cutting holds contour tolerances to around ±0.05 mm depending on thickness. Exact figures are confirmed against your drawing callouts.
Why is Tungsten Copper a good choice for CNC Laser Cutting?
Tungsten Copper is combines tungsten strength with copper conductivity, which makes it well suited to CNC Laser Cutting. We tune the process to the alloy so the finished Tungsten Copper cutting part meets your dimensional and functional requirements.
What is CNC Laser Cutting Tungsten Copper and how is it done?
CNC Laser Cutting Tungsten Copper refers to cNC fiber laser cutting follows a programmed path to cut sheet and plate with a clean, narrow kerf. Applied to Tungsten Copper — combines tungsten strength with copper conductivity — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Does CNC Laser Cutting Tungsten Copper require dedicated tooling?
Most Tungsten Copper cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.