CNC Laser Cutting Nickel is a core capability at VT machining. We combine controlled cutting with material-aware setup for Nickel — an alloy that is corrosion and heat resistant — to produce parts that meet your specification first time.
CNC Laser Cutting Capability for Nickel
- Fiber 1–6 kW
- Kerf 0.1–0.3 mm
- Contour ±0.05 mm
- N₂/O₂ assist gas
Nickel Material Data
| Density | 8.89 g/cm³ |
|---|---|
| Tensile strength | 460 MPa |
| Yield strength (0.2%) | 148 MPa |
| Hardness | 110 HB |
| Melting point | 1435–1446 °C |
| Thermal conductivity | 70 W/m·K |
| Thermal expansion | 13.3 ×10⁻⁶/K |
| Electrical conductivity | 23% |
| Machinability (C36000 = 100%) | 30% |
| Grades we run | Nickel 200, Nickel 201, Alloy 400, Alloy 600 |
Published typical values for Nickel 200. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Gummy and work-hardening at once. Sharp tools, positive rake, and a deliberate depth of cut that stays under the hardened skin from the previous pass.
How CNC Laser Cutting Nickel Works
A focused fibre-laser beam melts and blows material from the Nickel sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Laser Cutting Nickel
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Working with Nickel
As a material, Nickel is corrosion and heat resistant. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Design Tips for CNC Laser Cutting Nickel
We are happy to suggest design tweaks that improve manufacturability. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Nickel. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
Finished Nickel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
CNC Laser Cutting Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Nickel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
CNC Laser Cutting Tolerances & Surface Finish
Laser-cut Nickel holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Applications of CNC Laser Cutting Nickel
Customers order CNC Laser Cutting Nickel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Laser Cutting Nickel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Nickel
Three representative CNC Laser Cutting Nickel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
EMI shield can
- Material
- Nickel
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Battery busbar
- Material
- Nickel
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
Bracket blank
- Material
- Nickel
- Size
- 250 × 120 × 4 mm
- Key callouts
- Contour ±0.10 mm, bend-relief notches
- Batch
- 800 pcs
Bend reliefs cut in at the same time so the press brake does not tear the corner.
Finishing Options for Nickel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Laser Cutting Nickel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Nickel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Laser Cutting
Other Processes for Nickel
Send the drawing, the Nickel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is CNC Laser Cutting Nickel and how is it done?
CNC Laser Cutting Nickel refers to cNC fiber laser cutting follows a programmed path to cut sheet and plate with a clean, narrow kerf. Applied to Nickel — corrosion and heat resistant — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Can VT machining make custom Nickel parts to my drawing?
Yes. Nickel Nickel cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
Why is Nickel a good choice for CNC Laser Cutting?
Nickel is corrosion and heat resistant, which makes it well suited to CNC Laser Cutting. We tune the process to the alloy so the finished Nickel cutting part meets your dimensional and functional requirements.
What is the typical lead time and minimum order for CNC Laser Cutting Nickel?
CNC Laser Cutting prototypes for Nickel can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
What surface finish is achievable on Nickel with CNC Laser Cutting?
Laser cutting leaves a clean cut face on Nickel with a small heat-affected zone; most parts need little secondary finishing.