Looking for reliable CNC Sinker EDM Beryllium Copper? VT machining manufactures Beryllium Copper parts to tight tolerances and consistent quality. Beryllium Copper is high strength with good conductivity and fatigue life, so the process is set up specifically for the material.
CNC Sinker EDM Capability for Beryllium Copper
- Blind cavities & ribs
- Fine surface (VDI grades)
- Tolerance to ±0.005 mm
- Hardened tool steel
Beryllium Copper Material Data
| Density | 8.25 g/cm³ |
|---|---|
| Tensile strength | 1140–1380 MPa |
| Yield strength (0.2%) | 1000–1200 MPa |
| Hardness | 36–42 HRC |
| Melting point | 866–980 °C |
| Thermal conductivity | 105–130 W/m·K |
| Thermal expansion | 17.8 ×10⁻⁶/K |
| Electrical conductivity | 22% |
| Machinability (C36000 = 100%) | 20–35% |
| Grades we run | C17200, C17300, C17510 (high conductivity), C17410 |
Published typical values for C17200 (TH04/AT). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Machined in the solution-annealed state and age-hardened afterwards, which shrinks the part by roughly 0.1–0.2%. That shrink is compensated in the program.
How CNC Sinker EDM Beryllium Copper Works
Material is removed from the Beryllium Copper workpiece by controlled electrical discharges across a dielectric gap, with no mechanical contact. Flushing, on/off pulse timing and electrode/wire feed are set to balance speed against surface finish.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Sinker EDM Beryllium Copper
| Feature | Standard | Precision |
|---|---|---|
| Profile dimension | ±0.010 mm | ±0.002 mm |
| Internal corner radius | 0.15 mm | 0.05 mm |
| Taper control over 50 mm | 0.02 mm | 0.005 mm |
| Surface finish (skim passes) | Ra 0.8 µm | Ra 0.2 µm |
| Recast layer | 10 µm | 2 µm (fine skim) |
| Start-hole diameter | 1.0 mm | 0.25 mm |
| Workpiece hardness | no limit (conductive) | no limit (conductive) |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Sinker EDM Tolerances & Surface Finish
EDM holds tolerances to roughly ±0.002–0.005 mm with no cutting force on the Beryllium Copper part, producing fine, controlled surface textures and sharp internal corners impossible to mill.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Working with Beryllium Copper
As a material, Beryllium Copper is high strength with good conductivity and fatigue life. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Design Tips for CNC Sinker EDM Beryllium Copper
We are happy to suggest design tweaks that improve manufacturability. EDM suits sharp internal corners, thin ribs and hardened Beryllium Copper that cannot be milled; allowing a small corner radius where possible speeds the cut. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Sinker EDM Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Beryllium Copper part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Secondary Operations & Finishing
Finished Beryllium Copper parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Sinker EDM Beryllium Copper
Customers order CNC Sinker EDM Beryllium Copper components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Sinker EDM Beryllium Copper
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Beryllium Copper
Three representative CNC Sinker EDM Beryllium Copper jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Micro slot in nozzle
- Material
- Beryllium Copper
- Size
- 0.15 mm wide × 6 mm deep
- Key callouts
- Width ±0.003 mm
- Batch
- 400 pcs
Cut with 0.1 mm wire; the start hole is EDM-drilled at Ø0.3 mm.
Carbide punch
- Material
- Beryllium Copper
- Size
- Ø6 × 45 mm
- Key callouts
- OD ±0.003 mm, sharp form retained
- Batch
- 250 pcs
Carbide is EDM or grind only; there is no milling route.
Spline broach section
- Material
- Beryllium Copper
- Size
- Ø28 × 40 mm
- Key callouts
- Involute profile ±0.005 mm, Ra 0.4 µm
- Batch
- 60 pcs
Wire EDM after hardening to 62 HRC — the profile would not survive being cut soft and heat-treated.
Finishing Options for Beryllium Copper
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Sinker EDM Beryllium Copper
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Beryllium Copper grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Sinker EDM
Other Processes for Beryllium Copper
Send the drawing, the Beryllium Copper grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What tolerances can you hold for CNC Sinker EDM Beryllium Copper?
Achievable tolerances for Beryllium Copper EDM machining depend on the alloy, geometry and feature size. EDM holds tolerances to around ±0.002 mm with no cutting force on the part. Exact figures are confirmed against your drawing callouts.
How clean are the edges produced by CNC Sinker EDM on Beryllium Copper?
Machined Beryllium Copper edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What surface finish is achievable on Beryllium Copper with CNC Sinker EDM?
Surface finish on Beryllium Copper is controlled to your specification; we confirm the achievable Ra against your callout.
Which industries use CNC Sinker EDM Beryllium Copper parts?
CNC Sinker EDM Beryllium Copper parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Beryllium Copper components are required.
Can you EDM-machine hardened Beryllium Copper?
Yes. EDM removes material by electrical discharge rather than cutting force, so hardened and difficult Beryllium Copper can be machined to fine detail and tight tolerance without distortion.