CNC Press Brake Forming Bronze is a core capability at VT machining. We combine controlled forming with material-aware setup for Bronze — an alloy that is wear resistant with good bearing properties — to produce parts that meet your specification first time.
CNC Press Brake Forming Capability for Bronze
- Tonnage matched to material
- Air, bottom & coining
- Repeatable bend angles
- Long-part capability
Bronze Material Data
| Density | 8.80 g/cm³ |
|---|---|
| Tensile strength | 240 MPa |
| Yield strength (0.2%) | 125 MPa |
| Hardness | 65 HB |
| Melting point | 855–980 °C |
| Thermal conductivity | 59 W/m·K |
| Thermal expansion | 18.0 ×10⁻⁶/K |
| Electrical conductivity | 12% |
| Machinability (C36000 = 100%) | 70% |
| Grades we run | C93200 SAE 660, C54400, C63000 aluminium bronze, C86300 manganese bronze |
Published typical values for C93200 (SAE 660). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Cast bearing bronze has porosity. On sealing faces we specify continuous-cast stock rather than sand-cast, because a pinhole in a bore face is not repairable.
How CNC Press Brake Forming Bronze Works
The Bronze blank is bent or formed against tooling under CNC-controlled ram travel and back-gauge positioning. Bend allowance and springback are compensated in the program so finished angles hit the print.
Every job begins from your CAD model or 2D drawing. Fixturing and tool paths are planned so the most critical dimensions are produced in the most rigid, repeatable setup. Critical dimensions are checked on the first part and monitored through the run.
Achievable Tolerances for CNC Press Brake Forming Bronze
| Feature | Standard | Precision |
|---|---|---|
| Bend angle | ±1.0° | ±0.5° |
| Flange length | ±0.30 mm | ±0.15 mm |
| Hole-to-bend distance | ±0.30 mm | ±0.15 mm |
| Minimum inside radius | 1.0 × thickness | 0.8 × thickness |
| Minimum flange height | 4 × thickness + radius | 3 × thickness + radius |
| Bend-to-bend spacing | ±0.30 mm | ±0.15 mm |
| Sheet thickness range | 0.5–8.0 mm | 0.5–4.0 mm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Press Brake Forming Quality & Inspection
Consistent quality comes from disciplined process control. Critical dimensions on Bronze parts are checked in-process and verified at final inspection using calibrated instruments and, where required, CMM measurement. Full documentation — dimensional reports, mill certs, FAIR — is available when your programme needs it.
Design Tips for CNC Press Brake Forming Bronze
A few design choices make a real difference to cost and quality. Consistent bend radii, adequate flange lengths and grain-direction awareness reduce cracking and springback in formed Bronze. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
We complete Bronze components with the secondary steps your drawing calls for. We arrange heat treatment, surface treatment, marking and assembly as needed. Tell us the final spec and we will plan the full route so parts arrive ready to use.
CNC Press Brake Forming Tolerances & Surface Finish
Formed Bronze holds bend angles to about ±0.5° and consistent flange dimensions, with bend allowance compensated for the material and thickness.
Final tolerances are governed by the material's behaviour, wall thickness and overall stiffness. We give honest DFM feedback if a callout would be costly or better achieved another way.
Working with Bronze
Bronze offers a useful combination of properties: it is wear resistant with good bearing properties. Those characteristics shape how we approach forming — from tool and parameter selection to work-holding and coolant.
If your application is sensitive to alloy condition, we agree the specification in writing and document it. Stock is sourced from reputable suppliers so what you order is what you receive.
Applications of CNC Press Brake Forming Bronze
CNC Press Brake Forming of Bronze supports parts across aerospace, medical, automotive, electronics, semiconductor, energy and general industrial sectors. We scale from one-off prototypes to ongoing production while holding the same quality.
How to Order CNC Press Brake Forming Bronze
Ordering Bronze parts is straightforward. Provide the drawing, material, quantity and any certification needs. Our engineers reply — in English — with feasibility, pricing and a realistic lead time, usually within one business day.
Parts We Have Run in Bronze
Three representative CNC Press Brake Forming Bronze jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
U-channel
- Material
- Bronze
- Size
- 800 mm long, 3 mm thick
- Key callouts
- Angle ±0.5°, straightness 1 mm over length
- Batch
- 250 pcs
Formed in two hits with a rotating die to avoid marking the outside face.
Hemmed panel edge
- Material
- Bronze
- Size
- 400 mm hem, 1.2 mm
- Key callouts
- Hem flat to 0.3 mm
- Batch
- 1,500 pcs
Hemmed to remove the sharp edge without a secondary deburr operation.
Mounting bracket
- Material
- Bronze
- Size
- 120 × 60 mm, 2 bends
- Key callouts
- Angle ±0.5°, hole-to-bend ±0.15 mm
- Batch
- 3,000 pcs
Holes placed at least 2.5 × thickness from the bend line so they do not distort.
Finishing Options for Bronze
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Press Brake Forming Bronze
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Bronze grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Press Brake Forming
Other Processes for Bronze
Send the drawing, the Bronze grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is the typical lead time and minimum order for CNC Press Brake Forming Bronze?
CNC Press Brake Forming prototypes for Bronze can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
What material thickness or size range suits CNC Press Brake Forming Bronze?
We form Bronze sheet and plate to your developed flat pattern and bend sequence.
Can VT machining make custom Bronze parts to my drawing?
Yes. Bronze Bronze forming is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
How clean are the edges produced by CNC Press Brake Forming on Bronze?
Machined Bronze edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What is CNC Press Brake Forming Bronze and how is it done?
CNC Press Brake Forming Bronze refers to press brake forming creates bends and complex profiles with CNC-controlled ram depth and gauging. Applied to Bronze — wear resistant with good bearing properties — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What surface finish is achievable on Bronze with CNC Press Brake Forming?
Surface finish on Bronze is controlled to your specification; we confirm the achievable Ra against your callout.