Looking for reliable CNC Press Brake Forming Molybdenum? VT machining manufactures Molybdenum parts to tight tolerances and consistent quality. Molybdenum is very high melting point and thermal stability, so the process is set up specifically for the material.
CNC Press Brake Forming Capability for Molybdenum
- Tonnage matched to material
- Air, bottom & coining
- Repeatable bend angles
- Long-part capability
Molybdenum Material Data
| Density | 10.22 g/cm³ |
|---|---|
| Tensile strength | 550–900 MPa |
| Yield strength (0.2%) | 480 MPa |
| Hardness | 200–250 HV |
| Melting point | 2623 °C |
| Thermal conductivity | 138 W/m·K |
| Thermal expansion | 4.8 ×10⁻⁶/K |
| Electrical conductivity | 34% |
| Machinability (C36000 = 100%) | 30% |
| Grades we run | Pure Mo (99.95%), TZM, Mo-La, MoCu |
Published typical values for Pure Mo / TZM. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Below its ductile-to-brittle transition it chips rather than cuts. Sharp corners get a radius, and thin sections are wire-EDM cut instead of milled.
How CNC Press Brake Forming Molybdenum Works
The Molybdenum blank is bent or formed against tooling under CNC-controlled ram travel and back-gauge positioning. Bend allowance and springback are compensated in the program so finished angles hit the print.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Press Brake Forming Molybdenum
| Feature | Standard | Precision |
|---|---|---|
| Bend angle | ±1.0° | ±0.5° |
| Flange length | ±0.30 mm | ±0.15 mm |
| Hole-to-bend distance | ±0.30 mm | ±0.15 mm |
| Minimum inside radius | 1.0 × thickness | 0.8 × thickness |
| Minimum flange height | 4 × thickness + radius | 3 × thickness + radius |
| Bend-to-bend spacing | ±0.30 mm | ±0.15 mm |
| Sheet thickness range | 0.5–8.0 mm | 0.5–4.0 mm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Press Brake Forming Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Molybdenum part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Design Tips for CNC Press Brake Forming Molybdenum
We are happy to suggest design tweaks that improve manufacturability. Consistent bend radii, adequate flange lengths and grain-direction awareness reduce cracking and springback in formed Molybdenum. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Press Brake Forming Tolerances & Surface Finish
Formed Molybdenum holds bend angles to about ±0.5° and consistent flange dimensions, with bend allowance compensated for the material and thickness.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Secondary Operations & Finishing
Finished Molybdenum parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Working with Molybdenum
As a material, Molybdenum is very high melting point and thermal stability. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Applications of CNC Press Brake Forming Molybdenum
Customers order CNC Press Brake Forming Molybdenum components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Press Brake Forming Molybdenum
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Molybdenum
Three representative CNC Press Brake Forming Molybdenum jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Radiused cover
- Material
- Molybdenum
- Size
- R150 × 500 mm
- Key callouts
- Radius ±1 mm, no tool marks
- Batch
- 200 pcs
Bumped in 14 small steps rather than rolled, because the batch does not justify a roll set.
Mounting bracket
- Material
- Molybdenum
- Size
- 120 × 60 mm, 2 bends
- Key callouts
- Angle ±0.5°, hole-to-bend ±0.15 mm
- Batch
- 3,000 pcs
Holes placed at least 2.5 × thickness from the bend line so they do not distort.
Sheet-metal enclosure
- Material
- Molybdenum
- Size
- 300 × 200 × 120 mm
- Key callouts
- Bend angle ±0.5°, diagonal ±0.5 mm
- Batch
- 400 pcs
Bend sequence chosen so no flange collides with the tool on the last hit.
Finishing Options for Molybdenum
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Press Brake Forming Molybdenum
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Molybdenum grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Press Brake Forming
Other Processes for Molybdenum
Send the drawing, the Molybdenum grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Press Brake Forming on Molybdenum?
Machined Molybdenum edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What tolerances can you hold for CNC Press Brake Forming Molybdenum?
Achievable tolerances for Molybdenum forming depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.
Can VT machining make custom Molybdenum parts to my drawing?
Yes. Molybdenum Molybdenum forming is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What material thickness or size range suits CNC Press Brake Forming Molybdenum?
We form Molybdenum sheet and plate to your developed flat pattern and bend sequence.
Why is Molybdenum a good choice for CNC Press Brake Forming?
Molybdenum is very high melting point and thermal stability, which makes it well suited to CNC Press Brake Forming. We tune the process to the alloy so the finished Molybdenum forming part meets your dimensional and functional requirements.