VT machining provides CNC 4-Axis Machining Molybdenum for customers who need accurate, repeatable Molybdenum components. Because Molybdenum is very high melting point and thermal stability, we adapt the process to suit — controlling the variables that matter for this alloy.
CNC 4-Axis Machining Capability for Molybdenum
- Indexed & continuous 4th axis
- Multi-face in one setup
- Tolerance to ±0.01 mm
- Rotary fixturing
Molybdenum Material Data
| Density | 10.22 g/cm³ |
|---|---|
| Tensile strength | 550–900 MPa |
| Yield strength (0.2%) | 480 MPa |
| Hardness | 200–250 HV |
| Melting point | 2623 °C |
| Thermal conductivity | 138 W/m·K |
| Thermal expansion | 4.8 ×10⁻⁶/K |
| Electrical conductivity | 34% |
| Machinability (C36000 = 100%) | 30% |
| Grades we run | Pure Mo (99.95%), TZM, Mo-La, MoCu |
Published typical values for Pure Mo / TZM. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Below its ductile-to-brittle transition it chips rather than cuts. Sharp corners get a radius, and thin sections are wire-EDM cut instead of milled.
How CNC 4-Axis Machining Molybdenum Works
Rotating multi-flute cutters remove material as the Molybdenum workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC 4-Axis Machining Molybdenum
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC 4-Axis Machining Tolerances & Surface Finish
For CNC 4-Axis Machining, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
CNC 4-Axis Machining Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Design Tips for CNC 4-Axis Machining Molybdenum
Small design adjustments often cut cost and lead time. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Molybdenum. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
Most Molybdenum parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Working with Molybdenum
Molybdenum is very high melting point and thermal stability. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Applications of CNC 4-Axis Machining Molybdenum
Molybdenum parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC 4-Axis Machining Molybdenum
Starting your project takes one email. Send your CAD or 2D drawing, the Molybdenum grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Molybdenum
Three representative CNC 4-Axis Machining Molybdenum jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Manifold block
- Material
- Molybdenum
- Size
- 120 × 60 × 45 mm
- Key callouts
- Cross-bore intersection ±0.05 mm, ports G1/8", leak-tested to 10 bar
- Batch
- 80 pcs
Deburred internally with a brush tool; a burr at a cross-bore is what fails the leak test.
Heat sink base
- Material
- Molybdenum
- Size
- 200 × 100 × 8 mm
- Key callouts
- Fin thickness 1.2 ±0.05 mm, base flatness 0.03 mm
- Batch
- 500 pcs
Fins cut with a slotting cutter in one pass to avoid the deflection a step-over leaves.
Vacuum chamber flange
- Material
- Molybdenum
- Size
- Ø180 × 20 mm
- Key callouts
- Knife-edge seal Ra 0.4 µm, bolt circle ±0.05 mm
- Batch
- 60 pcs
Sealing face finished last, then handled in gloves and bagged straight off the machine.
Finishing Options for Molybdenum
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC 4-Axis Machining Molybdenum
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Molybdenum grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC 4-Axis Machining
Other Processes for Molybdenum
Send the drawing, the Molybdenum grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What surface finish is achievable on Molybdenum with CNC 4-Axis Machining?
Surface finish on Molybdenum is controlled to your specification; we confirm the achievable Ra against your callout.
Why is Molybdenum a good choice for CNC 4-Axis Machining?
Molybdenum is very high melting point and thermal stability, which makes it well suited to CNC 4-Axis Machining. We tune the process to the alloy so the finished Molybdenum machining part meets your dimensional and functional requirements.
Does CNC 4-Axis Machining Molybdenum require dedicated tooling?
Most Molybdenum machining work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
How clean are the edges produced by CNC 4-Axis Machining on Molybdenum?
Machined Molybdenum edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.