Looking for reliable CNC Laser Cutting Kovar? VT machining manufactures Kovar parts to tight tolerances and consistent quality. Kovar is matched thermal expansion for glass/ceramic seals, so the process is set up specifically for the material.
CNC Laser Cutting Capability for Kovar
- Fiber 1–6 kW
- Kerf 0.1–0.3 mm
- Contour ±0.05 mm
- N₂/O₂ assist gas
Kovar Material Data
| Density | 8.36 g/cm³ |
|---|---|
| Tensile strength | 517 MPa |
| Yield strength (0.2%) | 340 MPa |
| Hardness | 140–160 HV |
| Melting point | 1450 °C |
| Thermal conductivity | 17.3 W/m·K |
| Thermal expansion | 5.1 (30–200 °C) ×10⁻⁶/K |
| Electrical conductivity | 3.5% |
| Machinability (C36000 = 100%) | 35% |
| Grades we run | Kovar / ASTM F15, Alloy 42, Alloy 52 |
Published typical values for Kovar (ASTM F15). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Sealing surfaces must stay clean. Parts destined for glass-to-metal seals are degreased and handled without bare hands after final machining.
How CNC Laser Cutting Kovar Works
A focused fibre-laser beam melts and blows material from the Kovar sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Every job begins from your CAD model or 2D drawing. Fixturing and tool paths are planned so the most critical dimensions are produced in the most rigid, repeatable setup. Critical dimensions are checked on the first part and monitored through the run.
Achievable Tolerances for CNC Laser Cutting Kovar
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Secondary Operations & Finishing
We complete Kovar components with the secondary steps your drawing calls for. We arrange heat treatment, surface treatment, marking and assembly as needed. Tell us the final spec and we will plan the full route so parts arrive ready to use.
CNC Laser Cutting Quality & Inspection
Consistent quality comes from disciplined process control. Critical dimensions on Kovar parts are checked in-process and verified at final inspection using calibrated instruments and, where required, CMM measurement. Full documentation — dimensional reports, mill certs, FAIR — is available when your programme needs it.
Design Tips for CNC Laser Cutting Kovar
A few design choices make a real difference to cost and quality. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Kovar. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Laser Cutting Tolerances & Surface Finish
Laser-cut Kovar holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Final tolerances are governed by the material's behaviour, wall thickness and overall stiffness. We give honest DFM feedback if a callout would be costly or better achieved another way.
Working with Kovar
Kovar offers a useful combination of properties: it is matched thermal expansion for glass/ceramic seals. Those characteristics shape how we approach laser cutting — from tool and parameter selection to work-holding and coolant.
If your application is sensitive to alloy condition, we agree the specification in writing and document it. Stock is sourced from reputable suppliers so what you order is what you receive.
Applications of CNC Laser Cutting Kovar
CNC Laser Cutting of Kovar supports parts across aerospace, medical, automotive, electronics, semiconductor, energy and general industrial sectors. We scale from one-off prototypes to ongoing production while holding the same quality.
How to Order CNC Laser Cutting Kovar
Ordering Kovar parts is straightforward. Provide the drawing, material, quantity and any certification needs. Our engineers reply — in English — with feasibility, pricing and a realistic lead time, usually within one business day.
Parts We Have Run in Kovar
Three representative CNC Laser Cutting Kovar jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
EMI shield can
- Material
- Kovar
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Battery busbar
- Material
- Kovar
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
Bracket blank
- Material
- Kovar
- Size
- 250 × 120 × 4 mm
- Key callouts
- Contour ±0.10 mm, bend-relief notches
- Batch
- 800 pcs
Bend reliefs cut in at the same time so the press brake does not tear the corner.
Finishing Options for Kovar
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Laser Cutting Kovar
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Kovar grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Laser Cutting
Other Processes for Kovar
Send the drawing, the Kovar grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Laser Cutting on Kovar?
Laser cutting leaves Kovar with a narrow kerf and a clean, near burr-free edge and only a small heat-affected zone.
What is the typical lead time and minimum order for CNC Laser Cutting Kovar?
CNC Laser Cutting prototypes for Kovar can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
Why is Kovar a good choice for CNC Laser Cutting?
Kovar is matched thermal expansion for glass/ceramic seals, which makes it well suited to CNC Laser Cutting. We tune the process to the alloy so the finished Kovar cutting part meets your dimensional and functional requirements.
Does CNC Laser Cutting Kovar require dedicated tooling?
Most Kovar cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
Can VT machining make custom Kovar parts to my drawing?
Yes. Kovar Kovar cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What material thickness or size range suits CNC Laser Cutting Kovar?
Laser-cut Kovar thickness depends on the alloy and its reflectivity; we tune the fiber source and assist gas accordingly.