CNC EDM Drilling Spring Steel from VT machining delivers precision Spring Steel parts produced to your exact drawing. Fast-hole EDM drilling produces small, deep holes in hard metals, including starter holes for wire EDM, and we tune every parameter to the behaviour of Spring Steel, which is high yield strength and elastic recovery.
CNC EDM Drilling Capability for Spring Steel
- Ø0.2–3 mm holes
- Deep aspect ratios
- Hardened-metal drilling
- Angled hole capability
Spring Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 1200–1700 MPa |
| Yield strength (0.2%) | 1000–1500 MPa |
| Hardness | 44–50 HRC (tempered) |
| Melting point | 1425 °C |
| Thermal conductivity | 46 W/m·K |
| Thermal expansion | 11.4 ×10⁻⁶/K |
| Electrical conductivity | 8% |
| Machinability (C36000 = 100%) | 40% (annealed); grind or EDM when hardened |
| Grades we run | 1074, 1095, 65Mn, 60Si2Mn, 301 spring temper, 17-7PH |
Published typical values for 1095 / 65Mn. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Springback. Formed features are over-bent by a calculated amount; on flat springs we etch or wire-EDM instead of punching so the temper is untouched.
How CNC EDM Drilling Spring Steel Works
Material is removed from the Spring Steel workpiece by controlled electrical discharges across a dielectric gap, with no mechanical contact. Flushing, on/off pulse timing and electrode/wire feed are set to balance speed against surface finish.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC EDM Drilling Spring Steel
| Feature | Standard | Precision |
|---|---|---|
| Profile dimension | ±0.010 mm | ±0.002 mm |
| Internal corner radius | 0.15 mm | 0.05 mm |
| Taper control over 50 mm | 0.02 mm | 0.005 mm |
| Surface finish (skim passes) | Ra 0.8 µm | Ra 0.2 µm |
| Recast layer | 10 µm | 2 µm (fine skim) |
| Start-hole diameter | 1.0 mm | 0.25 mm |
| Workpiece hardness | no limit (conductive) | no limit (conductive) |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC EDM Drilling Spring Steel
Small design adjustments often cut cost and lead time. EDM suits sharp internal corners, thin ribs and hardened Spring Steel that cannot be milled; allowing a small corner radius where possible speeds the cut. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
Most Spring Steel parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
CNC EDM Drilling Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
CNC EDM Drilling Tolerances & Surface Finish
EDM holds tolerances to roughly ±0.002–0.005 mm with no cutting force on the Spring Steel part, producing fine, controlled surface textures and sharp internal corners impossible to mill.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Working with Spring Steel
Spring Steel is high yield strength and elastic recovery. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Applications of CNC EDM Drilling Spring Steel
Spring Steel parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC EDM Drilling Spring Steel
Starting your project takes one email. Send your CAD or 2D drawing, the Spring Steel grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Spring Steel
Three representative CNC EDM Drilling Spring Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Turbine blade fir-tree root
- Material
- Spring Steel
- Size
- 40 × 25 mm section
- Key callouts
- Profile ±0.008 mm
- Batch
- 120 pcs
Held on a dedicated fixture so every blade in the set indexes identically.
Extrusion die
- Material
- Spring Steel
- Size
- 120 × 120 × 25 mm
- Key callouts
- Profile ±0.005 mm, internal corner R0.1 mm
- Batch
- 35 pcs
Cut in four skim passes; the first pass is speed, the last three are finish and accuracy.
Spline broach section
- Material
- Spring Steel
- Size
- Ø28 × 40 mm
- Key callouts
- Involute profile ±0.005 mm, Ra 0.4 µm
- Batch
- 60 pcs
Wire EDM after hardening to 62 HRC — the profile would not survive being cut soft and heat-treated.
Finishing Options for Spring Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC EDM Drilling Spring Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Spring Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC EDM Drilling
Other Processes for Spring Steel
Send the drawing, the Spring Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What tolerances can you hold for CNC EDM Drilling Spring Steel?
Achievable tolerances for Spring Steel EDM machining depend on the alloy, geometry and feature size. EDM holds tolerances to around ±0.002 mm with no cutting force on the part. Exact figures are confirmed against your drawing callouts.
Does CNC EDM Drilling Spring Steel require dedicated tooling?
Wire EDM needs no shaped tooling; sinker EDM uses a shaped electrode we produce in-house for your cavity.
Why is Spring Steel a good choice for CNC EDM Drilling?
Spring Steel is high yield strength and elastic recovery, which makes it well suited to CNC EDM Drilling. We tune the process to the alloy so the finished Spring Steel EDM machining part meets your dimensional and functional requirements.
Can you EDM-machine hardened Spring Steel?
Yes. EDM removes material by electrical discharge rather than cutting force, so hardened and difficult Spring Steel can be machined to fine detail and tight tolerance without distortion.