Looking for reliable CNC Tapping Spring Steel? VT machining manufactures Spring Steel parts to tight tolerances and consistent quality. Spring Steel is high yield strength and elastic recovery, so the process is set up specifically for the material.
CNC Tapping Capability for Spring Steel
- Metric & UNC/UNF threads
- Rigid synchronized tapping
- Thread depth control
- Form and cut taps
Spring Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 1200–1700 MPa |
| Yield strength (0.2%) | 1000–1500 MPa |
| Hardness | 44–50 HRC (tempered) |
| Melting point | 1425 °C |
| Thermal conductivity | 46 W/m·K |
| Thermal expansion | 11.4 ×10⁻⁶/K |
| Electrical conductivity | 8% |
| Machinability (C36000 = 100%) | 40% (annealed); grind or EDM when hardened |
| Grades we run | 1074, 1095, 65Mn, 60Si2Mn, 301 spring temper, 17-7PH |
Published typical values for 1095 / 65Mn. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Springback. Formed features are over-bent by a calculated amount; on flat springs we etch or wire-EDM instead of punching so the temper is untouched.
How CNC Tapping Spring Steel Works
Rotating multi-flute cutters remove material as the Spring Steel workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Tapping Spring Steel
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Working with Spring Steel
Spring Steel is high yield strength and elastic recovery. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
CNC Tapping Tolerances & Surface Finish
For CNC Tapping, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Secondary Operations & Finishing
Most Spring Steel parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
CNC Tapping Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Design Tips for CNC Tapping Spring Steel
Small design adjustments often cut cost and lead time. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Spring Steel. If you send your model early, we will return practical DFM feedback before you commit to production.
Applications of CNC Tapping Spring Steel
Spring Steel parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Tapping Spring Steel
Starting your project takes one email. Send your CAD or 2D drawing, the Spring Steel grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Spring Steel
Three representative CNC Tapping Spring Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Sensor housing
- Material
- Spring Steel
- Size
- 86 × 54 × 22 mm
- Key callouts
- Pocket depth ±0.02 mm, bore H7, flatness 0.015 mm
- Batch
- 250 pcs / quarter
O-ring groove finished in the same setup as the sealing face so the two stay parallel.
Robot end-effector bracket
- Material
- Spring Steel
- Size
- 180 × 90 × 30 mm
- Key callouts
- Bore pair concentric within 0.02 mm, weight reduction pockets
- Batch
- 120 pcs
Pockets ganged so wall thickness never drops below 2 mm at the load path.
Vacuum chamber flange
- Material
- Spring Steel
- Size
- Ø180 × 20 mm
- Key callouts
- Knife-edge seal Ra 0.4 µm, bolt circle ±0.05 mm
- Batch
- 60 pcs
Sealing face finished last, then handled in gloves and bagged straight off the machine.
Finishing Options for Spring Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Tapping Spring Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Spring Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Tapping
Other Processes for Spring Steel
Send the drawing, the Spring Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is the typical lead time and minimum order for CNC Tapping Spring Steel?
CNC Tapping prototypes for Spring Steel can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
What is CNC Tapping Spring Steel and how is it done?
CNC Tapping Spring Steel refers to rigid CNC tapping cuts internal threads in sync with spindle feed for precise, repeatable thread engagement. Applied to Spring Steel — high yield strength and elastic recovery — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What tolerances can you hold for CNC Tapping Spring Steel?
Achievable tolerances for Spring Steel machining depend on the alloy, geometry and feature size. Milling holds positional and dimensional tolerances to around ±0.01 mm, tighter with precision setups. Exact figures are confirmed against your drawing callouts.
Why is Spring Steel a good choice for CNC Tapping?
Spring Steel is high yield strength and elastic recovery, which makes it well suited to CNC Tapping. We tune the process to the alloy so the finished Spring Steel machining part meets your dimensional and functional requirements.