CNC Surface Grinding Nickel is a core capability at VT machining. We combine controlled grinding with material-aware setup for Nickel — an alloy that is corrosion and heat resistant — to produce parts that meet your specification first time.
CNC Surface Grinding Capability for Nickel
- Flatness within 0.003 mm
- Ra to 0.1 µm
- Parallelism control
- Hardened-steel capable
Nickel Material Data
| Density | 8.89 g/cm³ |
|---|---|
| Tensile strength | 460 MPa |
| Yield strength (0.2%) | 148 MPa |
| Hardness | 110 HB |
| Melting point | 1435–1446 °C |
| Thermal conductivity | 70 W/m·K |
| Thermal expansion | 13.3 ×10⁻⁶/K |
| Electrical conductivity | 23% |
| Machinability (C36000 = 100%) | 30% |
| Grades we run | Nickel 200, Nickel 201, Alloy 400, Alloy 600 |
Published typical values for Nickel 200. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Gummy and work-hardening at once. Sharp tools, positive rake, and a deliberate depth of cut that stays under the hardened skin from the previous pass.
How CNC Surface Grinding Nickel Works
An abrasive wheel removes a fine, controlled layer from the Nickel part. Wheel specification, dressing interval, infeed and coolant are matched to the alloy's hardness so the surface is not burned or left with residual stress.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Surface Grinding Nickel
| Feature | Standard | Precision |
|---|---|---|
| Size (OD, ID, thickness) | ±0.005 mm | ±0.002 mm |
| Flatness over 100 mm | 0.010 mm | 0.003 mm |
| Parallelism | 0.010 mm | 0.003 mm |
| Roundness | 0.005 mm | 0.002 mm |
| Squareness | 0.010 mm | 0.005 mm |
| Surface finish | Ra 0.4 µm | Ra 0.1 µm |
| Workpiece hardness | up to 62 HRC | up to 65 HRC |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Surface Grinding Tolerances & Surface Finish
Ground Nickel reaches single-micron tolerances on size, flatness and parallelism, with surface finishes down to Ra 0.1–0.4 µm — and a near-mirror finish on suitable alloys.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Working with Nickel
As a material, Nickel is corrosion and heat resistant. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
CNC Surface Grinding Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Nickel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Secondary Operations & Finishing
Finished Nickel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Design Tips for CNC Surface Grinding Nickel
We are happy to suggest design tweaks that improve manufacturability. Allowing adequate grind stock, specifying realistic flatness over the true datum, and relieving corners help us hit tight tolerances on Nickel efficiently. If you send your model early, we will return practical DFM feedback before you commit to production.
Applications of CNC Surface Grinding Nickel
Customers order CNC Surface Grinding Nickel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Surface Grinding Nickel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Nickel
Three representative CNC Surface Grinding Nickel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Slitter blade
- Material
- Nickel
- Size
- Ø150 × 1.5 mm
- Key callouts
- Thickness ±0.005 mm, edge concentricity 0.005 mm
- Batch
- 400 pcs
Ground in a stack so all blades in a set share the same thickness.
Gauge block set
- Material
- Nickel
- Size
- 50 × 30 × 10 mm
- Key callouts
- Thickness ±0.002 mm, flatness 0.002 mm, parallelism 0.002 mm
- Batch
- 200 pcs
Ground wet in one chucking, then left to normalise before final inspection at 20 °C.
Punch tool
- Material
- Nickel
- Size
- Ø10 × 60 mm
- Key callouts
- OD ±0.002 mm, roundness 0.002 mm, Ra 0.1 µm
- Batch
- 300 pcs
Cylindrical ground after hardening to 60 HRC — machining soft would not hold the size.
Finishing Options for Nickel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Surface Grinding Nickel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Nickel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Surface Grinding
Other Processes for Nickel
Send the drawing, the Nickel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is the typical lead time and minimum order for CNC Surface Grinding Nickel?
CNC Surface Grinding prototypes for Nickel can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
How clean are the edges produced by CNC Surface Grinding on Nickel?
Machined Nickel edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What tolerances can you hold for CNC Surface Grinding Nickel?
Achievable tolerances for Nickel grinding depend on the alloy, geometry and feature size. Grinding routinely holds single-micron tolerances on diameter, flatness and parallelism. Exact figures are confirmed against your drawing callouts.
Does CNC Surface Grinding Nickel require dedicated tooling?
Most Nickel grinding work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What is CNC Surface Grinding Nickel and how is it done?
CNC Surface Grinding Nickel refers to surface grinding produces flat, parallel faces with fine finish using a horizontal abrasive wheel. Applied to Nickel — corrosion and heat resistant — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.