CNC Gear Hobbing Tungsten from VT machining delivers precision Tungsten parts produced to your exact drawing. Gear hobbing generates gear teeth with a rotating hob synchronized to the workpiece, and we tune every parameter to the behaviour of Tungsten, which is extreme hardness, density and heat resistance.
CNC Gear Hobbing Capability for Tungsten
- Spur & helical gears
- Module range support
- Pre-grind accuracy
- High productivity
Tungsten Material Data
| Density | 19.25 g/cm³ |
|---|---|
| Tensile strength | 750–1500 MPa |
| Yield strength (0.2%) | 550 MPa |
| Hardness | 350–500 HV |
| Melting point | 3422 °C |
| Thermal conductivity | 173 W/m·K |
| Thermal expansion | 4.5 ×10⁻⁶/K |
| Electrical conductivity | 31% |
| Machinability (C36000 = 100%) | grind / EDM only |
| Grades we run | Pure W (99.95%), W-Ni-Fe heavy alloy (17.0–18.5 g/cm³), WC-Co |
Published typical values for Pure W / W-Ni-Fe. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Conventional cutting is not on the table for pure tungsten. Features are wire-EDM cut and ground; expect longer lead time than any other metal on the list.
How CNC Gear Hobbing Tungsten Works
Tooth profiles are generated in the Tungsten blank by a synchronised cutter, then refined to the required accuracy class. Module, pressure angle and helix are programmed from your gear data.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Gear Hobbing Tungsten
| Feature | Standard | Precision |
|---|---|---|
| Accuracy class | DIN 8 / AGMA 10 | DIN 6 / AGMA 12 |
| Profile deviation | 0.020 mm | 0.008 mm |
| Lead deviation | 0.020 mm | 0.008 mm |
| Pitch deviation (cumulative) | 0.040 mm | 0.015 mm |
| Runout | 0.030 mm | 0.010 mm |
| Tooth surface finish | Ra 1.6 µm | Ra 0.4 µm (ground) |
| Module range | m0.5–m8 | m1–m6 |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Gear Hobbing Tungsten
Small design adjustments often cut cost and lead time. Providing complete gear data (module, pressure angle, profile shift, quality class) lets us produce Tungsten gears right the first time. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Gear Hobbing Tolerances & Surface Finish
Gear features are produced to a specified DIN/AGMA accuracy class, with profile and lead controlled for quiet, durable running under load.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
CNC Gear Hobbing Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Secondary Operations & Finishing
Most Tungsten parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Working with Tungsten
Tungsten is extreme hardness, density and heat resistance. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Applications of CNC Gear Hobbing Tungsten
Tungsten parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Gear Hobbing Tungsten
Starting your project takes one email. Send your CAD or 2D drawing, the Tungsten grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Tungsten
Three representative CNC Gear Hobbing Tungsten jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Worm and wheel set
- Material
- Tungsten
- Size
- m3, single start
- Key callouts
- Backlash 0.05–0.10 mm as a matched pair
- Batch
- 120 sets
Supplied as matched sets and marked, because mixing pairs loses the backlash spec.
Internal ring gear
- Material
- Tungsten
- Size
- m2.5, z72, ID 190 mm
- Key callouts
- DIN 8, pitch deviation 0.03 mm
- Batch
- 150 pcs
Shaped rather than hobbed — an internal gear leaves no room for a hob to run out.
Spur gear
- Material
- Tungsten
- Size
- m2, z40, 20° PA, face 20 mm
- Key callouts
- DIN 7, runout 0.02 mm
- Batch
- 500 pcs
Hobbed, hardened, then hard-finished; skipping the finish pass costs a full accuracy class.
Finishing Options for Tungsten
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Gear Hobbing Tungsten
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Gear Hobbing
Other Processes for Tungsten
Send the drawing, the Tungsten grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Gear Hobbing on Tungsten?
Machined Tungsten edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
What material thickness or size range suits CNC Gear Hobbing Tungsten?
We machine Tungsten across a broad size range; share your part envelope for confirmation.
Which industries use CNC Gear Hobbing Tungsten parts?
CNC Gear Hobbing Tungsten parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Tungsten components are required.
Does CNC Gear Hobbing Tungsten require dedicated tooling?
Most Tungsten gear cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.