Looking for reliable CNC Deburring Brass? VT machining manufactures Brass parts to tight tolerances and consistent quality. Brass is free-machining, good conductivity, attractive finish, so the process is set up specifically for the material.
Process Data for CNC Deburring Brass
| Recommended method | Brush / tumbling with non-ferrous media |
|---|---|
| Typical edge break | 0.1-0.3 mm or per drawing |
Shown for C360 Brass, the most common Brass grade we see for CNC Deburring. Typical values for C360 Brass, Half-hard; confirmed on the first part.
CNC Deburring Capability for Brass
- Edge-break control
- Burr-free edges
- Consistent radius
- High-volume capable
Brass material properties, finishing options and grade notes are on our CNC Polishing Brass page.
How CNC Deburring Brass Works
Abrasive media or tooling refine the Brass surface in controlled stages, removing the previous step's marks until the target roughness and edge condition are reached.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Deburring Brass
| Feature | Standard | Precision |
|---|---|---|
| Surface roughness | Ra 0.8 µm | Ra 0.05 µm |
| Edge break | 0.1–0.3 mm | 0.05 ±0.02 mm |
| Material removed | 0.02 mm | 0.005 mm |
| Bore roundness after honing | 0.005 mm | 0.002 mm |
| Cross-hatch angle | 45° ±10° | 45° ±5° |
| Cosmetic grade | uniform satin | mirror, no visible lines |
| Masking of datum faces | on request | standard |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Deburring Brass
Small design adjustments often cut cost and lead time. Telling us the target Ra, the cosmetic faces and any masking needs lets us finish Brass efficiently without over-processing. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Deburring Tolerances & Surface Finish
Finishing brings Brass to a defined roughness target — from a uniform satin to Ra values as low as 0.05 µm — with controlled, repeatable edge breaks.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Applications of CNC Deburring Brass
Brass parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
Typical Brass Parts for CNC Deburring
Illustrative examples of CNC Deburring Brass parts and the callouts that usually drive the process plan. They show the kind of work that fits this process; they are not specific customer orders.
Hydraulic bore
- Material
- Brass
- Size
- Ø32 × 200 mm
- Key callouts
- Ra 0.4 µm cross-hatch 45°, roundness 0.003 mm
- Batch
- 600 pcs
Honed in three stages; the cross-hatch is what holds the oil film.
Passivated stainless fitting
- Material
- Brass
- Size
- Ø18 × 40 mm
- Key callouts
- ASTM A967 citric passivation, no free iron
- Batch
- 5,000 pcs
Passivated after all machining, then tested with a copper sulphate check.
Mirror-polished insert
- Material
- Brass
- Size
- 80 × 50 mm cavity
- Key callouts
- Ra 0.05 µm, SPI A2
- Batch
- 60 pcs
Polished in five abrasive stages; skipping one leaves scratches the next cannot remove.
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Deburring Brass
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Brass grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Deburring
Other Processes for Brass
Send the drawing, the Brass grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What is CNC Deburring Brass and how is it done?
CNC Deburring Brass refers to automated deburring removes sharp edges and burrs for safe handling and consistent edge quality. Applied to Brass — free-machining, good conductivity, attractive finish — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What tolerances can you hold for CNC Deburring Brass?
Achievable tolerances for Brass finishing depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.
Does CNC Deburring Brass require dedicated tooling?
Most Brass finishing work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What is the typical lead time and minimum order for CNC Deburring Brass?
CNC Deburring prototypes for Brass can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.