Looking for reliable CNC Thread Grinding Brass? VT machining manufactures Brass parts to tight tolerances and consistent quality. Brass is free-machining, good conductivity, attractive finish, so the process is set up specifically for the material.
Process Data for CNC Thread Grinding Brass
| Wheel (supply condition) | Silicon carbide |
|---|---|
| Depth per pass (rough / finish) | 0.02-0.05 / 0.002-0.005 mm |
| Achievable finish | Ra 0.4-0.8 µm (soft metals load the wheel) |
| Typical size tolerance | Thread class 4h / lead ±0.003 mm per 25 mm |
Shown for C360 Brass, the most common Brass grade we see for CNC Thread Grinding. Typical values for C360 Brass, Half-hard; confirmed on the first part.
CNC Thread Grinding Capability for Brass
- Pitch accuracy to grade 3
- Hardened-part threading
- Lead screws & gauges
- Fine surface finish
Brass material properties, finishing options and grade notes are on our CNC Surface Grinding Brass page.
How CNC Thread Grinding Brass Works
An abrasive wheel removes a fine, controlled layer from the Brass part. Wheel specification, dressing interval, infeed and coolant are matched to the alloy's hardness so the surface is not burned or left with residual stress.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Thread Grinding Brass
| Feature | Standard | Precision |
|---|---|---|
| Size (OD, ID, thickness) | ±0.005 mm | ±0.002 mm |
| Flatness over 100 mm | 0.010 mm | 0.003 mm |
| Parallelism | 0.010 mm | 0.003 mm |
| Roundness | 0.005 mm | 0.002 mm |
| Squareness | 0.010 mm | 0.005 mm |
| Surface finish | Ra 0.4 µm | Ra 0.1 µm |
| Workpiece hardness | up to 62 HRC | up to 65 HRC |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Thread Grinding Tolerances & Surface Finish
Ground Brass reaches single-micron tolerances on size, flatness and parallelism, with surface finishes down to Ra 0.1–0.4 µm — and a near-mirror finish on suitable alloys.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Design Tips for CNC Thread Grinding Brass
Small design adjustments often cut cost and lead time. Allowing adequate grind stock, specifying realistic flatness over the true datum, and relieving corners help us hit tight tolerances on Brass efficiently. If you send your model early, we will return practical DFM feedback before you commit to production.
Applications of CNC Thread Grinding Brass
Brass parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
Typical Brass Parts for CNC Thread Grinding
Illustrative examples of CNC Thread Grinding Brass parts and the callouts that usually drive the process plan. They show the kind of work that fits this process; they are not specific customer orders.
Gauge block set
- Material
- Brass
- Size
- 50 × 30 × 10 mm
- Key callouts
- Thickness ±0.002 mm, flatness 0.002 mm, parallelism 0.002 mm
- Batch
- 200 pcs
Ground wet in one chucking, then left to normalise before final inspection at 20 °C.
Slitter blade
- Material
- Brass
- Size
- Ø150 × 1.5 mm
- Key callouts
- Thickness ±0.005 mm, edge concentricity 0.005 mm
- Batch
- 400 pcs
Ground in a stack so all blades in a set share the same thickness.
Lapping plate
- Material
- Brass
- Size
- 300 × 300 × 30 mm
- Key callouts
- Flatness 0.005 mm over the full face
- Batch
- 20 pcs
Ground, stress-relieved, ground again — one pass will not hold flatness on this area.
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Thread Grinding Brass
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Brass grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Thread Grinding
Other Processes for Brass
Send the drawing, the Brass grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Why is Brass a good choice for CNC Thread Grinding?
Brass is free-machining, good conductivity, attractive finish, which makes it well suited to CNC Thread Grinding. We tune the process to the alloy so the finished Brass grinding part meets your dimensional and functional requirements.
What surface finish is achievable on Brass with CNC Thread Grinding?
Grinding can take Brass to a fine finish — typically Ra 0.1–0.4 µm, and to a mirror grade on suitable alloys.
Which industries use CNC Thread Grinding Brass parts?
CNC Thread Grinding Brass parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Brass components are required.
Does CNC Thread Grinding Brass require dedicated tooling?
Most Brass grinding work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.