CNC Tapping Tungsten is a core capability at VT machining. We combine controlled machining with material-aware setup for Tungsten — an alloy that is extreme hardness, density and heat resistance — to produce parts that meet your specification first time.
CNC Tapping Capability for Tungsten
- Metric & UNC/UNF threads
- Rigid synchronized tapping
- Thread depth control
- Form and cut taps
Tungsten Material Data
| Density | 19.25 g/cm³ |
|---|---|
| Tensile strength | 750–1500 MPa |
| Yield strength (0.2%) | 550 MPa |
| Hardness | 350–500 HV |
| Melting point | 3422 °C |
| Thermal conductivity | 173 W/m·K |
| Thermal expansion | 4.5 ×10⁻⁶/K |
| Electrical conductivity | 31% |
| Machinability (C36000 = 100%) | grind / EDM only |
| Grades we run | Pure W (99.95%), W-Ni-Fe heavy alloy (17.0–18.5 g/cm³), WC-Co |
Published typical values for Pure W / W-Ni-Fe. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Conventional cutting is not on the table for pure tungsten. Features are wire-EDM cut and ground; expect longer lead time than any other metal on the list.
How CNC Tapping Tungsten Works
Rotating multi-flute cutters remove material as the Tungsten workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Tapping Tungsten
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Tapping Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Tungsten part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
CNC Tapping Tolerances & Surface Finish
For CNC Tapping, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Design Tips for CNC Tapping Tungsten
We are happy to suggest design tweaks that improve manufacturability. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Tungsten. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Tungsten
As a material, Tungsten is extreme hardness, density and heat resistance. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Secondary Operations & Finishing
Finished Tungsten parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Tapping Tungsten
Customers order CNC Tapping Tungsten components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Tapping Tungsten
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Tungsten
Three representative CNC Tapping Tungsten jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Heat sink base
- Material
- Tungsten
- Size
- 200 × 100 × 8 mm
- Key callouts
- Fin thickness 1.2 ±0.05 mm, base flatness 0.03 mm
- Batch
- 500 pcs
Fins cut with a slotting cutter in one pass to avoid the deflection a step-over leaves.
Manifold block
- Material
- Tungsten
- Size
- 120 × 60 × 45 mm
- Key callouts
- Cross-bore intersection ±0.05 mm, ports G1/8", leak-tested to 10 bar
- Batch
- 80 pcs
Deburred internally with a brush tool; a burr at a cross-bore is what fails the leak test.
Robot end-effector bracket
- Material
- Tungsten
- Size
- 180 × 90 × 30 mm
- Key callouts
- Bore pair concentric within 0.02 mm, weight reduction pockets
- Batch
- 120 pcs
Pockets ganged so wall thickness never drops below 2 mm at the load path.
Finishing Options for Tungsten
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Tapping Tungsten
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Tapping
Other Processes for Tungsten
Send the drawing, the Tungsten grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Does CNC Tapping Tungsten require dedicated tooling?
Most Tungsten machining work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
Can VT machining make custom Tungsten parts to my drawing?
Yes. Tungsten Tungsten machining is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What is CNC Tapping Tungsten and how is it done?
CNC Tapping Tungsten refers to rigid CNC tapping cuts internal threads in sync with spindle feed for precise, repeatable thread engagement. Applied to Tungsten — extreme hardness, density and heat resistance — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Why is Tungsten a good choice for CNC Tapping?
Tungsten is extreme hardness, density and heat resistance, which makes it well suited to CNC Tapping. We tune the process to the alloy so the finished Tungsten machining part meets your dimensional and functional requirements.
How clean are the edges produced by CNC Tapping on Tungsten?
Machined Tungsten edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.