Looking for reliable CNC Surface Grinding Bronze? VT machining manufactures Bronze parts to tight tolerances and consistent quality. Bronze is wear resistant with good bearing properties, so the process is set up specifically for the material.
CNC Surface Grinding Capability for Bronze
- Flatness within 0.003 mm
- Ra to 0.1 µm
- Parallelism control
- Hardened-steel capable
Bronze Material Data
| Density | 8.80 g/cm³ |
|---|---|
| Tensile strength | 240 MPa |
| Yield strength (0.2%) | 125 MPa |
| Hardness | 65 HB |
| Melting point | 855–980 °C |
| Thermal conductivity | 59 W/m·K |
| Thermal expansion | 18.0 ×10⁻⁶/K |
| Electrical conductivity | 12% |
| Machinability (C36000 = 100%) | 70% |
| Grades we run | C93200 SAE 660, C54400, C63000 aluminium bronze, C86300 manganese bronze |
Published typical values for C93200 (SAE 660). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Cast bearing bronze has porosity. On sealing faces we specify continuous-cast stock rather than sand-cast, because a pinhole in a bore face is not repairable.
How CNC Surface Grinding Bronze Works
An abrasive wheel removes a fine, controlled layer from the Bronze part. Wheel specification, dressing interval, infeed and coolant are matched to the alloy's hardness so the surface is not burned or left with residual stress.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Surface Grinding Bronze
| Feature | Standard | Precision |
|---|---|---|
| Size (OD, ID, thickness) | ±0.005 mm | ±0.002 mm |
| Flatness over 100 mm | 0.010 mm | 0.003 mm |
| Parallelism | 0.010 mm | 0.003 mm |
| Roundness | 0.005 mm | 0.002 mm |
| Squareness | 0.010 mm | 0.005 mm |
| Surface finish | Ra 0.4 µm | Ra 0.1 µm |
| Workpiece hardness | up to 62 HRC | up to 65 HRC |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Surface Grinding Tolerances & Surface Finish
Ground Bronze reaches single-micron tolerances on size, flatness and parallelism, with surface finishes down to Ra 0.1–0.4 µm — and a near-mirror finish on suitable alloys.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
CNC Surface Grinding Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Secondary Operations & Finishing
Most Bronze parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Design Tips for CNC Surface Grinding Bronze
Small design adjustments often cut cost and lead time. Allowing adequate grind stock, specifying realistic flatness over the true datum, and relieving corners help us hit tight tolerances on Bronze efficiently. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Bronze
Bronze is wear resistant with good bearing properties. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
Applications of CNC Surface Grinding Bronze
Bronze parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Surface Grinding Bronze
Starting your project takes one email. Send your CAD or 2D drawing, the Bronze grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Bronze
Three representative CNC Surface Grinding Bronze jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Punch tool
- Material
- Bronze
- Size
- Ø10 × 60 mm
- Key callouts
- OD ±0.002 mm, roundness 0.002 mm, Ra 0.1 µm
- Batch
- 300 pcs
Cylindrical ground after hardening to 60 HRC — machining soft would not hold the size.
Lapping plate
- Material
- Bronze
- Size
- 300 × 300 × 30 mm
- Key callouts
- Flatness 0.005 mm over the full face
- Batch
- 20 pcs
Ground, stress-relieved, ground again — one pass will not hold flatness on this area.
Slitter blade
- Material
- Bronze
- Size
- Ø150 × 1.5 mm
- Key callouts
- Thickness ±0.005 mm, edge concentricity 0.005 mm
- Batch
- 400 pcs
Ground in a stack so all blades in a set share the same thickness.
Finishing Options for Bronze
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Surface Grinding Bronze
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Bronze grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Surface Grinding
Other Processes for Bronze
Send the drawing, the Bronze grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Surface Grinding on Bronze?
Machined Bronze edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
Does CNC Surface Grinding Bronze require dedicated tooling?
Most Bronze grinding work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
Why is Bronze a good choice for CNC Surface Grinding?
Bronze is wear resistant with good bearing properties, which makes it well suited to CNC Surface Grinding. We tune the process to the alloy so the finished Bronze grinding part meets your dimensional and functional requirements.
What is CNC Surface Grinding Bronze and how is it done?
CNC Surface Grinding Bronze refers to surface grinding produces flat, parallel faces with fine finish using a horizontal abrasive wheel. Applied to Bronze — wear resistant with good bearing properties — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.