CNC Plasma Cutting Nickel Silver from VT machining delivers precision Nickel Silver parts produced to your exact drawing. CNC plasma cutting uses an ionized gas jet to sever thicker conductive plate at high speed, and we tune every parameter to the behaviour of Nickel Silver, which is corrosion resistant with a bright silver-white finish.
CNC Plasma Cutting Capability for Nickel Silver
- Plate to 30+ mm
- High cutting speed
- Conductive metals
- Bevel-cut capable
Nickel Silver Material Data
| Density | 8.73 g/cm³ |
|---|---|
| Tensile strength | 390–710 MPa |
| Yield strength (0.2%) | 170–545 MPa |
| Hardness | 70–160 HV |
| Melting point | 1110 °C |
| Thermal conductivity | 33 W/m·K |
| Thermal expansion | 16.2 ×10⁻⁶/K |
| Electrical conductivity | 6% |
| Machinability (C36000 = 100%) | 20–30% |
| Grades we run | C75200, C77000, C79200 free-cutting |
Published typical values for C75200 (65-18). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
It is bought for its colour as often as its properties, so cosmetic faces are masked through deburring and handled in gloves from the machine onward.
How CNC Plasma Cutting Nickel Silver Works
A focused fibre-laser beam melts and blows material from the Nickel Silver sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Every job begins from your CAD model or 2D drawing. Fixturing and tool paths are planned so the most critical dimensions are produced in the most rigid, repeatable setup. Critical dimensions are checked on the first part and monitored through the run.
Achievable Tolerances for CNC Plasma Cutting Nickel Silver
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Plasma Cutting Tolerances & Surface Finish
Laser-cut Nickel Silver holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Final tolerances are governed by the material's behaviour, wall thickness and overall stiffness. We give honest DFM feedback if a callout would be costly or better achieved another way.
CNC Plasma Cutting Quality & Inspection
Consistent quality comes from disciplined process control. Critical dimensions on Nickel Silver parts are checked in-process and verified at final inspection using calibrated instruments and, where required, CMM measurement. Full documentation — dimensional reports, mill certs, FAIR — is available when your programme needs it.
Design Tips for CNC Plasma Cutting Nickel Silver
A few design choices make a real difference to cost and quality. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Nickel Silver. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Nickel Silver
Nickel Silver offers a useful combination of properties: it is corrosion resistant with a bright silver-white finish. Those characteristics shape how we approach laser cutting — from tool and parameter selection to work-holding and coolant.
If your application is sensitive to alloy condition, we agree the specification in writing and document it. Stock is sourced from reputable suppliers so what you order is what you receive.
Secondary Operations & Finishing
We complete Nickel Silver components with the secondary steps your drawing calls for. We arrange heat treatment, surface treatment, marking and assembly as needed. Tell us the final spec and we will plan the full route so parts arrive ready to use.
Applications of CNC Plasma Cutting Nickel Silver
CNC Plasma Cutting of Nickel Silver supports parts across aerospace, medical, automotive, electronics, semiconductor, energy and general industrial sectors. We scale from one-off prototypes to ongoing production while holding the same quality.
How to Order CNC Plasma Cutting Nickel Silver
Ordering Nickel Silver parts is straightforward. Provide the drawing, material, quantity and any certification needs. Our engineers reply — in English — with feasibility, pricing and a realistic lead time, usually within one business day.
Parts We Have Run in Nickel Silver
Three representative CNC Plasma Cutting Nickel Silver jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Machine guard panel
- Material
- Nickel Silver
- Size
- 900 × 600 × 3 mm
- Key callouts
- Slot pattern ±0.10 mm, hole-to-edge 6 mm
- Batch
- 150 pcs
Cut with common-line pairs to halve the pierce count.
Gasket / shim set
- Material
- Nickel Silver
- Size
- Ø120 × 0.5 mm
- Key callouts
- ID/OD ±0.05 mm, no heat discolouration
- Batch
- 3,000 pcs
Small-diameter holes below 1.2 × thickness are punched, not lased.
Battery busbar
- Material
- Nickel Silver
- Size
- 180 × 30 × 2 mm
- Key callouts
- Contour ±0.08 mm, hole ±0.05 mm
- Batch
- 2,000 pcs
Copper is cut on the fibre laser with a reflective-material head; not every shop can run it.
Finishing Options for Nickel Silver
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Plasma Cutting Nickel Silver
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Nickel Silver grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Plasma Cutting
Other Processes for Nickel Silver
Send the drawing, the Nickel Silver grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Can VT machining make custom Nickel Silver parts to my drawing?
Yes. Nickel Silver Nickel Silver cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What tolerances can you hold for CNC Plasma Cutting Nickel Silver?
Achievable tolerances for Nickel Silver cutting depend on the alloy, geometry and feature size. Laser cutting holds contour tolerances to around ±0.05 mm depending on thickness. Exact figures are confirmed against your drawing callouts.
Which industries use CNC Plasma Cutting Nickel Silver parts?
CNC Plasma Cutting Nickel Silver parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Nickel Silver components are required.
What surface finish is achievable on Nickel Silver with CNC Plasma Cutting?
Laser cutting leaves a clean cut face on Nickel Silver with a small heat-affected zone; most parts need little secondary finishing.
Does CNC Plasma Cutting Nickel Silver require dedicated tooling?
Most Nickel Silver cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What is CNC Plasma Cutting Nickel Silver and how is it done?
CNC Plasma Cutting Nickel Silver refers to cNC plasma cutting uses an ionized gas jet to sever thicker conductive plate at high speed. Applied to Nickel Silver — corrosion resistant with a bright silver-white finish — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.