CNC Honing Spring Steel from VT machining delivers precision Spring Steel parts produced to your exact drawing. Honing finishes bores with abrasive stones to precise size, roundness and a cross-hatch surface, and we tune every parameter to the behaviour of Spring Steel, which is high yield strength and elastic recovery.
CNC Honing Capability for Spring Steel
- Bore Ra to 0.1 µm
- Cross-hatch pattern
- Roundness within 0.002 mm
- Hydraulic-bore finishing
Spring Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 1200–1700 MPa |
| Yield strength (0.2%) | 1000–1500 MPa |
| Hardness | 44–50 HRC (tempered) |
| Melting point | 1425 °C |
| Thermal conductivity | 46 W/m·K |
| Thermal expansion | 11.4 ×10⁻⁶/K |
| Electrical conductivity | 8% |
| Machinability (C36000 = 100%) | 40% (annealed); grind or EDM when hardened |
| Grades we run | 1074, 1095, 65Mn, 60Si2Mn, 301 spring temper, 17-7PH |
Published typical values for 1095 / 65Mn. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Springback. Formed features are over-bent by a calculated amount; on flat springs we etch or wire-EDM instead of punching so the temper is untouched.
How CNC Honing Spring Steel Works
Abrasive media or tooling refine the Spring Steel surface in controlled stages, removing the previous step's marks until the target roughness and edge condition are reached.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Honing Spring Steel
| Feature | Standard | Precision |
|---|---|---|
| Surface roughness | Ra 0.8 µm | Ra 0.05 µm |
| Edge break | 0.1–0.3 mm | 0.05 ±0.02 mm |
| Material removed | 0.02 mm | 0.005 mm |
| Bore roundness after honing | 0.005 mm | 0.002 mm |
| Cross-hatch angle | 45° ±10° | 45° ±5° |
| Cosmetic grade | uniform satin | mirror, no visible lines |
| Masking of datum faces | on request | standard |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Honing Tolerances & Surface Finish
Finishing brings Spring Steel to a defined roughness target — from a uniform satin to Ra values as low as 0.05 µm — with controlled, repeatable edge breaks.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
CNC Honing Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Spring Steel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Design Tips for CNC Honing Spring Steel
We are happy to suggest design tweaks that improve manufacturability. Telling us the target Ra, the cosmetic faces and any masking needs lets us finish Spring Steel efficiently without over-processing. If you send your model early, we will return practical DFM feedback before you commit to production.
Working with Spring Steel
As a material, Spring Steel is high yield strength and elastic recovery. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Secondary Operations & Finishing
Finished Spring Steel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Honing Spring Steel
Customers order CNC Honing Spring Steel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Honing Spring Steel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Spring Steel
Three representative CNC Honing Spring Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Sealing face
- Material
- Spring Steel
- Size
- Ø60 mm face
- Key callouts
- Ra 0.2 µm, flatness 0.005 mm
- Batch
- 1,000 pcs
Lapped after grinding; the seal spec is a roughness number, not a dimension.
Mirror-polished insert
- Material
- Spring Steel
- Size
- 80 × 50 mm cavity
- Key callouts
- Ra 0.05 µm, SPI A2
- Batch
- 60 pcs
Polished in five abrasive stages; skipping one leaves scratches the next cannot remove.
Passivated stainless fitting
- Material
- Spring Steel
- Size
- Ø18 × 40 mm
- Key callouts
- ASTM A967 citric passivation, no free iron
- Batch
- 5,000 pcs
Passivated after all machining, then tested with a copper sulphate check.
Finishing Options for Spring Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Honing Spring Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Spring Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Honing
Other Processes for Spring Steel
Send the drawing, the Spring Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Does CNC Honing Spring Steel require dedicated tooling?
Most Spring Steel finishing work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What is the typical lead time and minimum order for CNC Honing Spring Steel?
CNC Honing prototypes for Spring Steel can be produced quickly and scaled to series production. Send your drawing and quantity and we will advise lead time and any minimum order.
What is CNC Honing Spring Steel and how is it done?
CNC Honing Spring Steel refers to honing finishes bores with abrasive stones to precise size, roundness and a cross-hatch surface. Applied to Spring Steel — high yield strength and elastic recovery — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What tolerances can you hold for CNC Honing Spring Steel?
Achievable tolerances for Spring Steel finishing depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.
What surface finish is achievable on Spring Steel with CNC Honing?
Our finishing processes refine Spring Steel surfaces to Ra values as low as 0.05 µm for cosmetic or sealing faces.