VT machining provides CNC Plasma Cutting Spring Steel for customers who need accurate, repeatable Spring Steel components. Because Spring Steel is high yield strength and elastic recovery, we adapt the process to suit — controlling the variables that matter for this alloy.
CNC Plasma Cutting Capability for Spring Steel
- Plate to 30+ mm
- High cutting speed
- Conductive metals
- Bevel-cut capable
Spring Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 1200–1700 MPa |
| Yield strength (0.2%) | 1000–1500 MPa |
| Hardness | 44–50 HRC (tempered) |
| Melting point | 1425 °C |
| Thermal conductivity | 46 W/m·K |
| Thermal expansion | 11.4 ×10⁻⁶/K |
| Electrical conductivity | 8% |
| Machinability (C36000 = 100%) | 40% (annealed); grind or EDM when hardened |
| Grades we run | 1074, 1095, 65Mn, 60Si2Mn, 301 spring temper, 17-7PH |
Published typical values for 1095 / 65Mn. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Springback. Formed features are over-bent by a calculated amount; on flat springs we etch or wire-EDM instead of punching so the temper is untouched.
How CNC Plasma Cutting Spring Steel Works
A focused fibre-laser beam melts and blows material from the Spring Steel sheet along the programmed contour. Power, focal position, nozzle stand-off and assist-gas pressure are tuned to the alloy and thickness for a clean, square edge.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Plasma Cutting Spring Steel
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Plasma Cutting Spring Steel
We are happy to suggest design tweaks that improve manufacturability. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on Spring Steel. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Plasma Cutting Tolerances & Surface Finish
Laser-cut Spring Steel holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Working with Spring Steel
As a material, Spring Steel is high yield strength and elastic recovery. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
CNC Plasma Cutting Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Spring Steel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Secondary Operations & Finishing
Finished Spring Steel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Applications of CNC Plasma Cutting Spring Steel
Customers order CNC Plasma Cutting Spring Steel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Plasma Cutting Spring Steel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Spring Steel
Three representative CNC Plasma Cutting Spring Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Machine guard panel
- Material
- Spring Steel
- Size
- 900 × 600 × 3 mm
- Key callouts
- Slot pattern ±0.10 mm, hole-to-edge 6 mm
- Batch
- 150 pcs
Cut with common-line pairs to halve the pierce count.
Gasket / shim set
- Material
- Spring Steel
- Size
- Ø120 × 0.5 mm
- Key callouts
- ID/OD ±0.05 mm, no heat discolouration
- Batch
- 3,000 pcs
Small-diameter holes below 1.2 × thickness are punched, not lased.
EMI shield can
- Material
- Spring Steel
- Size
- 60 × 45 × 0.3 mm
- Key callouts
- Contour ±0.05 mm, tab width 0.5 mm
- Batch
- 5,000 pcs
Nested 96-up per sheet; nesting is where the cost comes out of a part this small.
Finishing Options for Spring Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Plasma Cutting Spring Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Spring Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Plasma Cutting
Other Processes for Spring Steel
Send the drawing, the Spring Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
What surface finish is achievable on Spring Steel with CNC Plasma Cutting?
Laser cutting leaves a clean cut face on Spring Steel with a small heat-affected zone; most parts need little secondary finishing.
Which industries use CNC Plasma Cutting Spring Steel parts?
CNC Plasma Cutting Spring Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Spring Steel components are required.
Why is Spring Steel a good choice for CNC Plasma Cutting?
Spring Steel is high yield strength and elastic recovery, which makes it well suited to CNC Plasma Cutting. We tune the process to the alloy so the finished Spring Steel cutting part meets your dimensional and functional requirements.
Can VT machining make custom Spring Steel parts to my drawing?
Yes. Spring Steel Spring Steel cutting is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
What is CNC Plasma Cutting Spring Steel and how is it done?
CNC Plasma Cutting Spring Steel refers to cNC plasma cutting uses an ionized gas jet to sever thicker conductive plate at high speed. Applied to Spring Steel — high yield strength and elastic recovery — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.