CNC Engraving Titanium is a core capability at VT machining. We combine controlled machining with material-aware setup for Titanium — an alloy that is high strength-to-weight, biocompatible, corrosion resistant — to produce parts that meet your specification first time.
CNC Engraving Capability for Titanium
- Depth control to 0.02 mm
- Fine fonts & logos
- Serial / data-matrix marking
- Conical and ball engravers
Titanium Material Data
| Density | 4.43 g/cm³ |
|---|---|
| Tensile strength | 950 MPa |
| Yield strength (0.2%) | 880 MPa |
| Hardness | 334 HB / 36 HRC |
| Melting point | 1604–1660 °C |
| Thermal conductivity | 6.7 W/m·K |
| Thermal expansion | 8.6 ×10⁻⁶/K |
| Electrical conductivity | 3.1% |
| Machinability (C36000 = 100%) | 22% |
| Grades we run | Gr 1, Gr 2 (CP), Gr 5 Ti-6Al-4V, Gr 23 ELI, Gr 7, Gr 9 |
Published typical values for Ti-6Al-4V (Gr 5). Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Heat has nowhere to go — thermal conductivity is 1/25th of aluminium, so it all goes into the tool. Low surface speed, heavy feed, flood coolant, and the cutter never stops moving.
How CNC Engraving Titanium Works
Rotating multi-flute cutters remove material as the Titanium workpiece is driven through programmed tool paths on 3-, 4- or 5-axis machining centres. Climb milling, step-over and depth-of-cut are set so chip load stays in the ideal band for the alloy.
We start from your supplied geometry and tolerance scheme. The setup is designed to minimise re-clamping, which protects positional accuracy across features. A first article is verified against the drawing before the balance of the batch is released.
Achievable Tolerances for CNC Engraving Titanium
| Feature | Standard | Precision |
|---|---|---|
| Linear dimension (< 100 mm) | ±0.05 mm | ±0.010 mm |
| Linear dimension (100–300 mm) | ±0.10 mm | ±0.025 mm |
| Hole diameter (reamed) | H9 | H7 |
| True position of hole pattern | ±0.10 mm | ±0.025 mm |
| Flatness over 100 mm | 0.05 mm | 0.015 mm |
| Perpendicularity | 0.10 mm | 0.020 mm |
| Surface finish, as machined | Ra 1.6 µm | Ra 0.4 µm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Engraving Tolerances & Surface Finish
For CNC Engraving, dimensional and positional tolerances around ±0.01 mm are routine, tightening toward ±0.005 mm on precision setups. Surface finish on machined faces typically falls in the Ra 0.4–1.6 µm range depending on tooling and pass strategy.
The tightest tolerances are reserved for the features your drawing flags as critical. Share your tolerance scheme and we will confirm what is realistic before quoting.
Design Tips for CNC Engraving Titanium
Small design adjustments often cut cost and lead time. Generous internal radii, sensible pocket depth-to-width ratios and avoiding very thin unsupported walls all reduce cost and improve accuracy in Titanium. If you send your model early, we will return practical DFM feedback before you commit to production.
Secondary Operations & Finishing
Most Titanium parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Working with Titanium
Titanium is high strength-to-weight, biocompatible, corrosion resistant. We translate those properties into a process plan: the right tooling, speeds, feeds and fixturing for the alloy.
Where the grade, temper or heat-treat condition matters to performance, we confirm it with you and can supply material certificates. Material is procured to recognised standards for consistent, repeatable results.
CNC Engraving Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Applications of CNC Engraving Titanium
Titanium parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Engraving Titanium
Starting your project takes one email. Send your CAD or 2D drawing, the Titanium grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Parts We Have Run in Titanium
Three representative CNC Engraving Titanium jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Heat sink base
- Material
- Titanium
- Size
- 200 × 100 × 8 mm
- Key callouts
- Fin thickness 1.2 ±0.05 mm, base flatness 0.03 mm
- Batch
- 500 pcs
Fins cut with a slotting cutter in one pass to avoid the deflection a step-over leaves.
Manifold block
- Material
- Titanium
- Size
- 120 × 60 × 45 mm
- Key callouts
- Cross-bore intersection ±0.05 mm, ports G1/8", leak-tested to 10 bar
- Batch
- 80 pcs
Deburred internally with a brush tool; a burr at a cross-bore is what fails the leak test.
Robot end-effector bracket
- Material
- Titanium
- Size
- 180 × 90 × 30 mm
- Key callouts
- Bore pair concentric within 0.02 mm, weight reduction pockets
- Batch
- 120 pcs
Pockets ganged so wall thickness never drops below 2 mm at the load path.
Finishing Options for Titanium
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Type II anodise | — | Colour coding, biocompatible |
| Type III anodise | — | Anti-galling for threaded and sliding parts |
| Passivation | — | ASTM F86 for implant-grade parts |
| Electropolish | 5–20 µm removed | Removes the machining layer for medical use |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Engraving Titanium
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Titanium grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Engraving
Other Processes for Titanium
Send the drawing, the Titanium grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Which industries use CNC Engraving Titanium parts?
CNC Engraving Titanium parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Titanium components are required.
Why is Titanium a good choice for CNC Engraving?
Titanium is high strength-to-weight, biocompatible, corrosion resistant, which makes it well suited to CNC Engraving. We tune the process to the alloy so the finished Titanium machining part meets your dimensional and functional requirements.
What surface finish is achievable on Titanium with CNC Engraving?
Surface finish on Titanium is controlled to your specification; we confirm the achievable Ra against your callout.
What material thickness or size range suits CNC Engraving Titanium?
We machine Titanium across a broad size range; share your part envelope for confirmation.