VT machining specialises in CNC Plasma Cutting S275JR Steel. Because S275JR Steel is strong, economical and widely available, and its machinability is good to excellent depending on carbon content; free-machining grades cut cleanly, we plan each job around the grade to protect accuracy and surface quality.
CNC Plasma Cutting Capability for S275JR Steel
- Carbon/low-alloy grades
- Economical & weldable
- Tolerance to ±0.02 mm
- Hardenable by heat treat
S275JR Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 585 MPa |
| Yield strength (0.2%) | 450 MPa |
| Hardness | 170 HB |
| Melting point | 1420–1460 °C |
| Thermal conductivity | 51.9 W/m·K |
| Thermal expansion | 11.5 ×10⁻⁶/K |
| Electrical conductivity | 9% |
| Machinability (C36000 = 100%) | 57% |
| Grades we run | 1018, 1045, 1215, A36, S45C, St37, 4140 (see alloy steel) |
Published typical values for 1045. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Rust. Bare steel flash-rusts within hours in a humid container, so parts are oiled or passivated before packing unless you specify otherwise.
Machining S275JR Steel with CNC Plasma Cutting
When cutting S275JR Steel, machinability is good to excellent depending on carbon content; free-machining grades cut cleanly. Our process plan reflects this so the finished part holds its tolerances without distortion or poor finish.
Documented parameters for S275JR Steel mean predictable cycle times and stable, repeatable results.
Achievable Tolerances for CNC Plasma Cutting S275JR Steel
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Plasma Cutting S275JR Steel
Small design adjustments often cut cost and lead time. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on S275JR Steel. If you send your model early, we will return practical DFM feedback before you commit to production.
Why S275JR Steel?
Customers select S275JR Steel for CNC Plasma Cutting because it is strong, economical and widely available. We handle grade verification and any required heat treatment or finishing.
CNC Plasma Cutting Tolerances & Surface Finish
Laser-cut S275JR Steel holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
CNC Plasma Cutting Quality & Inspection
Quality is built in, not inspected on. We monitor key features during the run and confirm them at final inspection, with CMM verification available for tight tolerances. We provide the inspection and traceability records your quality system requires.
Secondary Operations & Finishing
Most S275JR Steel parts need some finishing, which we manage in-house or through vetted partners. Options include deburring and edge-breaking, heat treatment, surface grinding, polishing, and plating or anodising for corrosion resistance and appearance. Give us the finished-part requirement and we will sequence every operation correctly.
Applications of CNC Plasma Cutting S275JR Steel
S275JR Steel parts made this way are found throughout aerospace, medical, automotive, electronics and industrial equipment. Prototype, bridge and production volumes are all welcome.
How to Order CNC Plasma Cutting S275JR Steel
Starting your project takes one email. Send your CAD or 2D drawing, the S275JR Steel grade and condition, the quantity and any finish or inspection requirements. We respond quickly with price, lead time and any DFM notes, in clear English.
Finishing Options for S275JR Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Black oxide | 1–2 µm | Mild corrosion resistance, no dimensional change |
| Zinc plate + clear/yellow | 5–12 µm | ASTM B633, general corrosion protection |
| Nickel plate (electroless) | 10–25 µm | Uniform in bores, 500 HV after bake |
| Phosphate | 5–10 µm | Paint key, mild lubricity |
| Powder coat | 60–120 µm | RAL colours |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Plasma Cutting S275JR Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact S275JR Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
S275JR Steel in Other Processes
Related
Send the drawing, the S275JR Steel condition and the quantity — pricing and lead time come back the same or next business day.
Request a QuoteFrequently Asked Questions
What is CNC Plasma Cutting S275JR Steel and how is it done?
CNC Plasma Cutting S275JR Steel refers to cNC plasma cutting uses an ionized gas jet to sever thicker conductive plate at high speed. Applied to S275JR Steel — strong, economical and widely available — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
What surface finish is achievable on S275JR Steel with CNC Plasma Cutting?
Laser cutting leaves a clean cut face on S275JR Steel with a small heat-affected zone; most parts need little secondary finishing.
Which industries use CNC Plasma Cutting S275JR Steel parts?
CNC Plasma Cutting S275JR Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise S275JR Steel components are required.
What tolerances can you hold for CNC Plasma Cutting S275JR Steel?
Achievable tolerances for S275JR Steel cutting depend on the alloy, geometry and feature size. Laser cutting holds contour tolerances to around ±0.05 mm depending on thickness. Exact figures are confirmed against your drawing callouts.