VT machining specialises in CNC Laser Cutting 1050 Aluminum. Because 1050 Aluminum is lightweight with excellent machinability, and its machinability is excellent; high cutting speeds and superb finishes achievable, we plan each job around the grade to protect accuracy and surface quality.
CNC Laser Cutting Capability for 1050 Aluminum
- Lightweight (~2.7 g/cm³)
- Excellent machinability
- Tolerance to ±0.01 mm
- Anodising-ready
1050 Aluminum Material Data
| Density | 2.70 g/cm³ |
|---|---|
| Tensile strength | 310 MPa |
| Yield strength (0.2%) | 276 MPa |
| Hardness | 95 HB |
| Melting point | 582–652 °C |
| Thermal conductivity | 167 W/m·K |
| Thermal expansion | 23.6 ×10⁻⁶/K |
| Electrical conductivity | 43% |
| Machinability (C36000 = 100%) | 190% |
| Grades we run | 6061, 6082, 6063, 7075-T6, 5052, 2024-T3, MIC-6 cast plate |
Published typical values for 6061-T6. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Thin walls relax after roughing. We rough, let the part stabilise, then finish — otherwise a 1.5 mm wall bows by more than the tolerance it was cut to.
Machining 1050 Aluminum with CNC Laser Cutting
1050 Aluminum behaves predictably under CNC Laser Cutting once parameters are dialled in: machinability is excellent; high cutting speeds and superb finishes achievable, and we tune the operation accordingly.
We hold reference parameters for this grade, so repeat orders of 1050 Aluminum run consistently from one batch to the next.
Achievable Tolerances for CNC Laser Cutting 1050 Aluminum
| Feature | Standard | Precision |
|---|---|---|
| Contour dimension | ±0.10 mm | ±0.05 mm |
| Hole diameter | ±0.10 mm | ±0.05 mm |
| Kerf width | 0.20 mm | 0.10 mm |
| Squareness of cut edge | 0.5° | 0.2° |
| Heat-affected zone | 0.15 mm | 0.05 mm (N₂ assist) |
| Minimum hole diameter | 1.2 × thickness | 1.0 × thickness |
| Edge condition | light dross | burr-free, N₂ cut |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
CNC Laser Cutting Tolerances & Surface Finish
Laser-cut 1050 Aluminum holds contour tolerances around ±0.05 mm depending on thickness, with a narrow kerf and a clean, near burr-free edge.
Final tolerances are governed by the material's behaviour, wall thickness and overall stiffness. We give honest DFM feedback if a callout would be costly or better achieved another way.
Why 1050 Aluminum?
1050 Aluminum is chosen when a part needs what this grade offers — it is lightweight with excellent machinability. We confirm the grade and any temper or heat-treat condition with you before machining.
Secondary Operations & Finishing
Finished 1050 Aluminum parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
CNC Laser Cutting Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every 1050 Aluminum part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
Design Tips for CNC Laser Cutting 1050 Aluminum
We are happy to suggest design tweaks that improve manufacturability. Keeping holes no smaller than the material thickness, allowing for kerf, and grouping features sensibly improves edge quality and nesting yield on 1050 Aluminum. If you send your model early, we will return practical DFM feedback before you commit to production.
Applications of CNC Laser Cutting 1050 Aluminum
Customers order CNC Laser Cutting 1050 Aluminum components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Laser Cutting 1050 Aluminum
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Finishing Options for 1050 Aluminum
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Clear anodise (Type II) | 5–25 µm | Corrosion protection, keeps the natural colour |
| Colour anodise | 10–25 µm | Black, red, blue, gold; add 0.02 mm to close tolerances |
| Hard anodise (Type III) | 25–50 µm | 60–70 HRC surface, grows 50% into the part |
| Chromate / Alodine 1200 | < 1 µm | Conductive, meets MIL-DTL-5541 |
| Powder coat | 60–120 µm | RAL colours, needs 0.3 mm clearance on mating features |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Laser Cutting 1050 Aluminum
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact 1050 Aluminum grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
1050 Aluminum in Other Processes
Related
Send the drawing, the 1050 Aluminum condition and the quantity — pricing and lead time come back the same or next business day.
Request a QuoteFrequently Asked Questions
What material thickness or size range suits CNC Laser Cutting 1050 Aluminum?
Laser-cut 1050 Aluminum thickness depends on the alloy and its reflectivity; we tune the fiber source and assist gas accordingly.
What tolerances can you hold for CNC Laser Cutting 1050 Aluminum?
Achievable tolerances for 1050 Aluminum cutting depend on the alloy, geometry and feature size. Laser cutting holds contour tolerances to around ±0.05 mm depending on thickness. Exact figures are confirmed against your drawing callouts.
Does CNC Laser Cutting 1050 Aluminum require dedicated tooling?
Most 1050 Aluminum cutting work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What is CNC Laser Cutting 1050 Aluminum and how is it done?
CNC Laser Cutting 1050 Aluminum refers to cNC fiber laser cutting follows a programmed path to cut sheet and plate with a clean, narrow kerf. Applied to 1050 Aluminum — lightweight with excellent machinability — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.
Which industries use CNC Laser Cutting 1050 Aluminum parts?
CNC Laser Cutting 1050 Aluminum parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise 1050 Aluminum components are required.