Looking for reliable CNC Grinding Steel? VT machining manufactures Steel parts to tight tolerances and consistent quality. Steel is strong, economical, widely available carbon/alloy grades, so the process is set up specifically for the material.
CNC Grinding Capability for Steel
- Surface finish to Ra 0.1–0.4 µm
- Dimensional tolerance to ±0.002 mm
- Flatness/parallelism within 0.005 mm
- Wheel grit selected per alloy hardness
Steel Material Data
| Density | 7.85 g/cm³ |
|---|---|
| Tensile strength | 585 MPa |
| Yield strength (0.2%) | 450 MPa |
| Hardness | 170 HB |
| Melting point | 1420–1460 °C |
| Thermal conductivity | 51.9 W/m·K |
| Thermal expansion | 11.5 ×10⁻⁶/K |
| Electrical conductivity | 9% |
| Machinability (C36000 = 100%) | 57% |
| Grades we run | 1018, 1045, 1215, A36, S45C, St37, 4140 (see alloy steel) |
Published typical values for 1045. Other grades in the family differ — the certificate supplied with your order carries the actual heat-lot figures.
Rust. Bare steel flash-rusts within hours in a humid container, so parts are oiled or passivated before packing unless you specify otherwise.
How CNC Grinding Steel Works
An abrasive wheel removes a fine, controlled layer from the Steel part. Wheel specification, dressing interval, infeed and coolant are matched to the alloy's hardness so the surface is not burned or left with residual stress.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Grinding Steel
| Feature | Standard | Precision |
|---|---|---|
| Size (OD, ID, thickness) | ±0.005 mm | ±0.002 mm |
| Flatness over 100 mm | 0.010 mm | 0.003 mm |
| Parallelism | 0.010 mm | 0.003 mm |
| Roundness | 0.005 mm | 0.002 mm |
| Squareness | 0.010 mm | 0.005 mm |
| Surface finish | Ra 0.4 µm | Ra 0.1 µm |
| Workpiece hardness | up to 62 HRC | up to 65 HRC |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Working with Steel
As a material, Steel is strong, economical, widely available carbon/alloy grades. Our setup reflects the alloy's machinability so the finished part is accurate and free of avoidable defects.
We verify the exact grade and condition before machining, and traceable mill certs are available on request. We can work to your nominated material source or specification when required.
Secondary Operations & Finishing
Finished Steel parts can move straight into secondary operations under one roof. Typical add-ons are deburring, passivation, anodising, plating, blasting, polishing and laser marking. We coordinate the whole chain so you receive complete, inspection-ready parts.
Design Tips for CNC Grinding Steel
We are happy to suggest design tweaks that improve manufacturability. Allowing adequate grind stock, specifying realistic flatness over the true datum, and relieving corners help us hit tight tolerances on Steel efficiently. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Grinding Quality & Inspection
We control quality throughout the process, not just at the end. In-process checks plus final inspection — including CMM where specified — keep every Steel part to print. Inspection reports, material certificates and first-article documentation can be supplied on request.
CNC Grinding Tolerances & Surface Finish
Ground Steel reaches single-micron tolerances on size, flatness and parallelism, with surface finishes down to Ra 0.1–0.4 µm — and a near-mirror finish on suitable alloys.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Applications of CNC Grinding Steel
Customers order CNC Grinding Steel components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
How to Order CNC Grinding Steel
Getting a quote is simple. Share your model, the material grade, your quantity and target tolerances. You receive a clear quotation with lead time and honest manufacturability feedback.
Parts We Have Run in Steel
Three representative CNC Grinding Steel jobs, with the callouts that actually drove the process plan. Yours will differ — these are here so you can judge whether your part is in our range before you spend time on an RFQ.
Ceramic-coated shaft journal
- Material
- Steel
- Size
- Ø45 × 180 mm
- Key callouts
- OD ±0.003 mm, roundness 0.002 mm, Ra 0.2 µm
- Batch
- 150 pcs
Ground after coating; the coating is never the final dimension.
Mould insert
- Material
- Steel
- Size
- 80 × 60 × 25 mm
- Key callouts
- Flatness 0.003 mm, squareness 0.005 mm
- Batch
- 90 pcs
Surface ground on all six faces so the insert seats without shimming.
Slitter blade
- Material
- Steel
- Size
- Ø150 × 1.5 mm
- Key callouts
- Thickness ±0.005 mm, edge concentricity 0.005 mm
- Batch
- 400 pcs
Ground in a stack so all blades in a set share the same thickness.
Finishing Options for Steel
| Finish | Thickness / effect | Why it gets specified |
|---|---|---|
| Black oxide | 1–2 µm | Mild corrosion resistance, no dimensional change |
| Zinc plate + clear/yellow | 5–12 µm | ASTM B633, general corrosion protection |
| Nickel plate (electroless) | 10–25 µm | Uniform in bores, 500 HV after bake |
| Phosphate | 5–10 µm | Paint key, mild lubricity |
| Powder coat | 60–120 µm | RAL colours |
| Deburr / edge break | 0.05–0.3 mm | All parts unless the drawing says otherwise |
| Bead blast | Ra 1.6–3.2 µm | Uniform matt finish, hides tool marks |
| Laser marking | — | Part number, lot code, data matrix |
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Grinding Steel
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Steel grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Grinding
Other Processes for Steel
Send the drawing, the Steel grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
Does CNC Grinding Steel require dedicated tooling?
Most Steel grinding work uses standard cutting tools and CNC programs; dedicated fixtures are made only when geometry or volume requires them.
What material thickness or size range suits CNC Grinding Steel?
We machine Steel across a broad size range; share your part envelope for confirmation.
What surface finish is achievable on Steel with CNC Grinding?
Grinding can take Steel to a fine finish — typically Ra 0.1–0.4 µm, and to a mirror grade on suitable alloys.
Which industries use CNC Grinding Steel parts?
CNC Grinding Steel parts are used across aerospace, medical, automotive, electronics, semiconductor and general industrial sectors — anywhere precise Steel components are required.
What is CNC Grinding Steel and how is it done?
CNC Grinding Steel refers to cNC grinding removes material with a precision abrasive wheel to achieve tight dimensional tolerances and superior surface finish. Applied to Steel — strong, economical, widely available carbon/alloy grades — VT machining produces each part to your CAD drawing, selecting parameters from your tolerance, finish and quantity requirements.