CNC Press Brake Forming Tungsten from VT machining delivers precision Tungsten parts produced to your exact drawing. Press brake forming creates bends and complex profiles with CNC-controlled ram depth and gauging, and we tune every parameter to the behaviour of Tungsten, which is extreme hardness, density and heat resistance.
Process Data for CNC Press Brake Forming Tungsten
| Minimum inside bend radius | ~3 × t (across the grain) |
|---|---|
| Press force, 2 mm sheet, V16 die | ~39.8 t per metre |
| Typical springback at 90° | 0.5-1° |
| Angle tolerance | ±0.5° (CNC back-gauge, angle measurement on first part) |
| Tooling | Sectional punches, multi-V dies, hemming and offset tools |
Shown for Tungsten, the most common Tungsten grade we see for CNC Press Brake Forming. Typical values for Tungsten, Stress-relieved; confirmed on the first part.
CNC Press Brake Forming Capability for Tungsten
- Tonnage matched to material
- Air, bottom & coining
- Repeatable bend angles
- Long-part capability
Tungsten material properties, finishing options and grade notes are on our CNC Bending Tungsten page.
How CNC Press Brake Forming Tungsten Works
The Tungsten blank is bent or formed against tooling under CNC-controlled ram travel and back-gauge positioning. Bend allowance and springback are compensated in the program so finished angles hit the print.
Programming is driven directly by your 3D model or print. Work-holding, tool selection and the cutting strategy are planned around the critical features and the material before the first chip is cut. First-off inspection confirms the process is centred before production continues.
Achievable Tolerances for CNC Press Brake Forming Tungsten
| Feature | Standard | Precision |
|---|---|---|
| Bend angle | ±1.0° | ±0.5° |
| Flange length | ±0.30 mm | ±0.15 mm |
| Hole-to-bend distance | ±0.30 mm | ±0.15 mm |
| Minimum inside radius | 1.0 × thickness | 0.8 × thickness |
| Minimum flange height | 4 × thickness + radius | 3 × thickness + radius |
| Bend-to-bend spacing | ±0.30 mm | ±0.15 mm |
| Sheet thickness range | 0.5–8.0 mm | 0.5–4.0 mm |
Standard is what a normal quotation assumes. Precision is available on nominated features and is priced separately, because it needs extra setups, in-process gauging and CMM verification. Call out only the features that need it — blanket-tightening a drawing is the single most common reason a quote comes back expensive.
Design Tips for CNC Press Brake Forming Tungsten
We are happy to suggest design tweaks that improve manufacturability. Consistent bend radii, adequate flange lengths and grain-direction awareness reduce cracking and springback in formed Tungsten. If you send your model early, we will return practical DFM feedback before you commit to production.
CNC Press Brake Forming Tolerances & Surface Finish
Formed Tungsten holds bend angles to about ±0.5° and consistent flange dimensions, with bend allowance compensated for the material and thickness.
Exact achievable figures depend on the alloy, the feature size and the part geometry. Tell us which dimensions are critical and we will advise feasibility up front.
Applications of CNC Press Brake Forming Tungsten
Customers order CNC Press Brake Forming Tungsten components for everything from instrumentation to structural and functional assemblies. Whether you need a single prototype or recurring production volume, the same process discipline applies.
Typical Tungsten Parts for CNC Press Brake Forming
Illustrative examples of CNC Press Brake Forming Tungsten parts and the callouts that usually drive the process plan. They show the kind of work that fits this process; they are not specific customer orders.
U-channel
- Material
- Tungsten
- Size
- 800 mm long, 3 mm thick
- Key callouts
- Angle ±0.5°, straightness 1 mm over length
- Batch
- 250 pcs
Formed in two hits with a rotating die to avoid marking the outside face.
Hemmed panel edge
- Material
- Tungsten
- Size
- 400 mm hem, 1.2 mm
- Key callouts
- Hem flat to 0.3 mm
- Batch
- 1,500 pcs
Hemmed to remove the sharp edge without a secondary deburr operation.
Radiused cover
- Material
- Tungsten
- Size
- R150 × 500 mm
- Key callouts
- Radius ±1 mm, no tool marks
- Batch
- 200 pcs
Bumped in 14 small steps rather than rolled, because the batch does not justify a roll set.
No drawing yet? Build one in the browser.
Set the metal, dimensions and features, watch the 3D model update as you type, then switch to the 2D sheet to add dimensions and tolerances. Download it or send it straight to us with your RFQ.
What We Need to Quote CNC Press Brake Forming Tungsten
- GeometrySTEP or IGES for the 3D model, plus a PDF drawing if you have tolerance callouts. A dimensioned sketch is enough to start.
- MaterialThe exact Tungsten grade and condition — temper, heat-treat state or hardness. If you are not sure, tell us the function and we will suggest one.
- QuantityPrototype count and the expected annual volume. Both change how the part is made and therefore what it costs.
- TolerancesWhich features are critical. Everything else runs to our standard tolerance, which is what keeps the price sensible.
- FinishSurface treatment, cosmetic requirements, and any faces that must be masked.
- DocumentsWhether you need a material certificate, dimensional report, FAIR or PPAP with the shipment.
Missing something from the list is not a problem — send what you have. We will come back with the specific questions rather than a generic form.
Other Metals for CNC Press Brake Forming
Other Processes for Tungsten
Send the drawing, the Tungsten grade and the quantity. You get pricing, lead time and any DFM notes back — usually within one business day.
Request a QuoteFrequently Asked Questions
How clean are the edges produced by CNC Press Brake Forming on Tungsten?
Machined Tungsten edges are clean and to specification; edge-break or deburring is added when your drawing calls for it.
Can VT machining make custom Tungsten parts to my drawing?
Yes. Tungsten forming is made to order from your CAD/2D drawing. Share your geometry, material grade, tolerance and quantity and we will confirm feasibility, lead time and pricing.
Why is Tungsten a good choice for CNC Press Brake Forming?
Tungsten is extreme hardness, density and heat resistance, which makes it well suited to CNC Press Brake Forming. We tune the process to the alloy so the finished Tungsten forming part meets your dimensional and functional requirements.
What surface finish is achievable on Tungsten with CNC Press Brake Forming?
Surface finish on Tungsten is controlled to your specification; we confirm the achievable Ra against your callout.
What tolerances can you hold for CNC Press Brake Forming Tungsten?
Achievable tolerances for Tungsten forming depend on the alloy, geometry and feature size. We hold tight, repeatable tolerances appropriate to the feature and material. Exact figures are confirmed against your drawing callouts.